旋转滑动摩擦副摩擦噪声影响因素实验研究

doi:10.3969/j.issn.1004-132X.2020.23.005

摘要/Abstract

摘要： 为探究滑动摩擦噪声的影响因素，采用单因素实验法分析了表面粗糙度、相对速度、载荷、摩擦副材料、润滑油中石墨烯质量分数对滑动摩擦噪声的影响。实验发现:实验所测摩擦噪声可大体分为前期、中期、稳定期；表面粗糙度越小，摩擦噪声越小；转速升高时，摩擦噪声逐渐增大，但随着转速的增大，摩擦降噪增幅有所下降；适当增大载荷有助于降噪；石墨烯的降噪效果优异；陶瓷摩擦副比轴承钢摩擦副更具降噪优势。

关键词: 滑动摩擦, 噪声, 石墨烯, 实验

Abstract: In order to explore the influence factors of sliding friction noises, a single factor experimental method was used to analyze the influences of surface roughness, relative velocity, load, friction pair material, and mass fraction of graphene in lubricating oil on sliding friction noises. Friction noises measured during the experiments were roughly divided into early stage, middle stage, and stable stage. The lower the surface roughness, the lower the friction noises. When rotation speed increases, the friction noises increase gradually. With the increases of rotation speeds, the growth rate declineds. Appropriate increases of loads are helpful to noise reduction. Graphene has excellent noise reduction effectiveness. Ceramic friction pairs have more advantages than bearing steel friction pairs.

Key words: sliding friction, noise, graphene, experiment

中图分类号:

吴玉厚;张珈翊;张丽秀;王俊海. 旋转滑动摩擦副摩擦噪声影响因素实验研究[J]. 中国机械工程, DOI: 10.3969/j.issn.1004-132X.2020.23.005.

WU Yuhou;ZHANG Jiayi;ZHANG Lixiu;WANG Junhai.

Experimental Study on Influence Factors of Friction Noises for Rotating Sliding Friction Pairs

[J]. China Mechanical Engineering, DOI: 10.3969/j.issn.1004-132X.2020.23.005.

参考文献

［1］WANG Lin, HE Hui, LIN Rongtao, et al. Study on Ameliorating Friction Noise of ABS Materials by Lubrication［J］. Polymer Testing, 2020, 82(C):307-317.

［2］TU W, SHAO Y, MECHEFSKE C K. An Analytical Model to Investigate Skidding in Rolling Element Bearings during Acceleration［J］. Journal of Mechanical Science & Technology, 2012, 26(8):2451-2458.

［3］OBUNAI K, HAGIWARA S, OKUBO K, et al. Modification of Strain Distribution on Contact Surface of Shoe to Reduce Low Frequency Squeals for Brake Disc with Small Holes［J］. SAE Technical Papers, 2010(1):1715-1724.

［4］WANG X C, MO J L, WANG D W, et al. Experimental and Numerical Study of Friction-induced Noise of Brake Pad Materials Having Grooved Surface［J］. Mechanisms & Machine Science, 2015, 23:1043-1054.

［5］MATLAZIM A R, ABDUL HAMID M K, ABU BAKAR A R. Effects of Pad Surface Topography on Disc Brake Squeal［J］. Applied Mechanics and Materials, 2012, 165:58-62.

［6］单欢乐，莫继良，陈光雄，等. 沟槽形表面织构对摩擦噪声的影响［J］. 中国机械工程，2012，23(18):2233-2237.

SHAN Huanle, MO Jiliang, CHEN Guangxiong, et al. Effect of Grooved Surface Texture on Friction Noise ［J］. China Mechanical Engineering, 2012, 23 (18): 2233-2237.

［7］BLASCHKE P, TEJA MALLAREDDY T, PAESCHKE R, et al. Pressure Load Influence on Modal Parameters of a Brake Pad-disc Assembly and Their Characterization for Brake Squeal［C］//Eurobrake. Dresden, 2015：99-106.

［8］孙国辉，侯俊，张杰，等. 抑制盘式制动器振动噪声的阻尼层研究［J］. 武汉理工大学学报(信息与管理工程版), 2010, 32(6):954-957.

SUN Guohui, HOU Jun, ZHANG Jie, et al. Squeal Noise of Disc Brake with Damping Shim［J］. Journal of Wuhan University of Technology(Information & Management Engineering), 2010,32(6):954-957.

［9］CHIELLO O, SINOU J J, VINCENT N, et al. Squeal Noise Generated by Railway Disc Brakes: Experiments and Stability Computations on Large Industrial Models［J］. Journal of the Acoustical Society of America, 2013, 133(5):3461-3470.

［10］GHAZALY N, ABDO J. A Study of the Influence of Brake Pad Topography on the Generation of Brake Noise and Vibration［J］. Noise & Vibration in Industry, 2012, 26(4): 27-35.

［11］LAZIM A R M, HAMID M K A, JAMALUDDIN M R, et al. The Effect of Road Grit Particles on Brake Pad Surface Topography under Squealing Condition［C］//SAE 2012 Brake Colloquium & Exhibition. San Diego, 2012:1821-1829.

［12］MAT LAZIM A R, ABDUL HAMID M K, ABU BAKAR A R. Effects of Pad Surface Topography on Disc Brake Squeal［J］. Applied Mechanics and Materials, 2012, 165:58-62.

［13］MENG Huang. Statistical Analysis of Impacts of Surface Topography on Brake Squeal in Disc-Pad System［J］. SAE International Journal of Passenger Cars - Mechanical Systems, 2014(3): 933-944.

［14］LAZIM A R M, KCHAOU M, HAMID M K A, et al. Squealing Characteristics of Worn Brake Pads Due to Silica Sand Embedment into Their Friction Layers［J］. Wear, 2016(4): 123-136.

［15］ZHANG Zhendong, XU Shurong, ZHANG Jiangong, et al. Study on Vibration Noise Signal Characteristics of 10kV Distribution Transformer under Different Load Conditions［J］. IOP Conference Series: Materials Science and Engineering, 2019, 486(1)：33-41.

［16］王东伟，莫继良，陈光雄，等. 滑动摩擦振动噪声的非线性显式动力学分析［J］. 中国机械工程, 2014, 25(10): 1395-1399.

WANG Dongwei, MO Jiliang, CHEN Guangxiong, et al. Nonlinear Explicit Dynamic Analysis of Sliding Friction Vibration Noise［J］. China Mechanical Engineering, 2014, 25(10): 1395-1399.

［17］麦云飞, 刘志亮, 王书文, 等. 旋转滑动摩擦高频噪声产生机理的实验研究［J］.中国机械工程, 2017, 28(18): 2198-2203.

MAI Yunfei, LIU Zhiliang, WANG Shuwen, et al. Experimental Study on Mechanism of High Frequency Noise Caused by Rotating Sliding Friction［J］. China Mechanical Engineering, 2017, 28(18): 2198-2203.

［18］全鑫, 莫继良, 王安宇，等. 高速列车制动片摩擦块尺寸对制动噪声特性的影响［J］. 润滑与密封, 2019(9): 50-55.

QUAN Xin, MO Jiliang, WANG Anyu, et al. Effect of Brake Pad Size on Brake Noise Characteristics of High Speed Trains［J］. Lubrication and Sealing, 2019(9):50-55.

［19］李直, 陈剑, 沈锦龙, 等. 弹流润滑条件下表面形貌对摩擦噪声的影响［J］. 应用数学和力学, 2017, 38(7): 807-817.

LI Zhi, CHEN Jian, SHEN Jinlong, et al. Influence of Surface Topography on Friction Noise under Elastohydrodynamic Lubrication［J］. Applied Mathematics and Mechanics, 2017, 38(7):807-817.

［20］王冀军, 陈光雄. 接触共振频率与摩擦噪声频率之间关系的试验研究［J］. 摩擦学学报, 2014, 34(3): 278-284.

WANG Jijun, CHEN Guangxiong. Experimental Study on the Relationship between Contact Resonance Frequency and Friction Noise Frequency［J］. Journal of Tribology, 2014, 34(3): 278-284.

［21］佟钰, 李宛鸿, 董嘉, 等. 石墨烯改性润滑油的悬浮分散特性和摩擦学性能［J］. 材料研究学报, 2019, 33(1): 59-64.

TONG Yu, LI Wanhong, DONG Jia, et al. Suspension Dispersion and Tribological Properties of Graphene Modified Lubricants［J］. Journal of Materials Research, 2019, 33 (1): 59-64.

[1]	宋海生, 王磊, 田学武, 陈志勇. 基于振动控制的后视镜球铰摩擦能耗机理研究[J]. 中国机械工程, 2021, 32(06): 674-680.
[2]	谷正气, 刘壮志, 杨振东, 郑乐典, 尹善斌. 汽车风振噪声的空气射流结构优化[J]. 中国机械工程, 2021, 32(06): 681-688,733.
[3]	唐斌, 范志勇, 项载毓, 吴元科, 黄博, 莫继良, . [轮轨磨耗及预测]高速列车制动摩擦块切入端特征对制动界面特性的影响[J]. 中国机械工程, 2021, 32(04): 412-419.
[4]	秦亚璐1,3;蔡伟1,3;王留根1,3;雷政2;赵静一1,3;王启明2. 500m口径球面射电望远镜电液促动器系统空化影响的数值研究[J]. 中国机械工程, 2021, 32(02): 171-179.
[5]	沈诚;邹平;康迪;王文杰. 超声振动透镜辅助激光打孔实验研究[J]. 中国机械工程, 2020, 31(21): 2542-2546.
[6]	李迎春1，2;程蓓1;邱明1，2;谷守旭1;范恒华1. 不同石墨烯添加量下MoS2基复合涂层的摩擦磨损及耐腐蚀性能[J]. 中国机械工程, 2020, 31(20): 2437-2444.
[7]	焦东风;刘志峰. 低成本低噪声的驱动桥零部件精度优化方法[J]. 中国机械工程, 2020, 31(20): 2505-2511.
[8]	张丽霞, 庞齐齐, 潘福全, 葛小菡, 林炳钦, 何一超, 危银涛, 杜永昌. 磁流变减振器魔术公式模型在悬架控制中的应用[J]. 中国机械工程, 2020, 31(14): 1659-1665.
[9]	刘慧芳;徐浩添;高全祥;乔凯卿. 基于表面张力的微量点胶影响因素与规律分析[J]. 中国机械工程, 2020, 31(09): 1057-1064,1073.
[10]	邹一岚;文东辉;王扬渝;肖燏婷;邹磊. 超声振动光整的EDEM数值模拟与实验研究[J]. 中国机械工程, 2020, 31(06): 647-654,661.
[11]	李庆忠;孙苏磊;李强强. 单晶硅同质互抛实验研究[J]. 中国机械工程, 2019, 30(23): 2773-2777.
[12]	刘厚根;张攀. ZNR2.4罗茨机械增压器性能试验研究[J]. 中国机械工程, 2019, 30(23): 2843-2848.
[13]	宋志强1;曹立波1;欧阳志高1;邱洋迪2;陈凯2. 集成主被动式安全带的性能评估及优化分析[J]. 中国机械工程, 2019, 30(21): 2567-2576.
[14]	赵彦辰1;王掩刚1;刘汉儒1;秦江平2;张荣荣2. 航空发电机风阻实验及匹配冷却风扇设计[J]. 中国机械工程, 2019, 30(20): 2505-2511,2519.
[15]	李洪丞;马国喜;罗蓉;罗志勇. 基于实验设计与数据分析的金属热挤压成形比能耗优化[J]. 中国机械工程, 2019, 30(15): 1849-1855.