覆盖件模具拼接特征对球头刀铣削振动的影响

doi:10.3969/j.issn.1004-132X.2020.18.001

摘要/Abstract

摘要：

为了分析曲面拼接特征对振动的影响，建立了考虑拼接特征、曲面特征的未变形切屑厚度模型；基于曲面拼接区的未变形切屑厚度建立了考虑时滞变化的铣削动力学模型，通过数值计算综合分析了过拼接缝时冲击振动、刀具轴向位置角、拼接缝宽度对铣削振动的影响；最后基于淬硬钢曲面拼接铣削实验验证了考虑曲面拼接特征的铣削振动预测模型的准确性，并基于不同拼接特征下的铣削振动计算出了相应的加速度信号幅值和分形维数。研究结果表明:淬硬钢曲面拼接特征使铣削振动的非线性特征减弱，某一频段的振动能量集聚，据此情况可分析出不同拼接特征下的最佳加工工艺参数。

关键词: 拼接特征, 曲面铣削, 瞬时冲击, 铣削振动, 非线性分析

Abstract: In order to analyze the influences of the curved surface splicing characteristics on vibrations, an undistorted chip thickness model was established considering splicing characteristics and surface characteristics. Based on the undistorted chip thicknesses in the splicing areas of curved surfaces, a milling dynamics model was established considering the change of time delay. Through the numerical calculations, the influences of impact vibrations during the splicing seams, tool axial position angles and splicing seam widths on milling vibrations were analyzed comprehensively. Finally, based on the curved surface splicing milling experiments of hardened steels, the accuracy of milling vibration prediction model was verified considering the splicing surface characteristics. At the same time, the corresponding vibration acceleration signal amplitudes and fractal dimensions were calculated based on the milling vibrations under different splicing characteristics. The results show that the nonlinear characteristics of milling vibrations are weaken by the splicing characteristics of hardened steel surfaces, and vibration energy is concentrated in a certain frequency band. According to this situation, the optimal processing parameters may be analyzed under different splicing characteristics.

Key words: splicing characteristic, curved surface milling, instantaneous impact, milling vibration；nonlinear analysis

中图分类号:

TH16
O32

吴石；朱美文；张添源；刘献礼；李传东.

覆盖件模具拼接特征对球头刀铣削振动的影响

[J]. 中国机械工程, DOI: 10.3969/j.issn.1004-132X.2020.18.001.

WU Shi；ZHU Meiwen；ZHANG Tianyuan；LIU Xianli； LI Chuandong. Influences of Splicing Characteristics of Cover Panel Moulds on Milling Vibrations with Ball End Tools[J]. China Mechanical Engineering, DOI: 10.3969/j.issn.1004-132X.2020.18.001.

参考文献

[1]刘献礼，马晶，岳彩旭，等. 汽车模具凸曲面精加工极限切削深度预测[J]. 机械工程学报, 2015, 51(2)：117-126.
LIU Xianli, MA Jing, YUE Caixu, et al.Limit Cutting Depth Prediction for Automobile Dies Finishing Machining of Convex Surface[J].Journal of Mechanical Engineering, 2015, 51(2)：117-126.
[2]刘献礼，高海宁，岳彩旭，等. 拼接模具过缝区域切削力建模与表面质量[J]. 振动、测试与诊断， 2018, 38(3)：429-437.
LIU Xianli, GAO Haining, YUE Caixu, et al.Modeling of Cutting Force and Surface Quality in the Seam Area of Splicing Dies[J]. Journal of Vibration, Measurement and Diagnosis, 2018, 38(3)：429-437.
[3]YANG L, WU S, LIU X L, et al.The Effect of Characteristics of Free-form Surface on the Machined Surface Topography in Milling of Panel Mold[J].International Journal of Advanced Manufacturing Technology, 2018, 98(1/4) ：151-163.
[4]GUZEL B U, LAZOGLU L. An Enhanced Force Model for Sculptured Surface Maching[J]. Machining Science and Technology, 2004, 8(3)：431-448.
[5]SIM C, YANG M Y. The Prediction of the Cutting Force in Ball-end Milling with a Flexible Cutter[J]. International Journal of Machine Tools and Manufacture, 1993, 33(2)：267-284.
[6]WANG J J, HUANG C Y. A Force-model-based Approach to Estimating Cutter Axis Offset in Ball End Milling[J]. International Journal of Advanced Manufacturing Tecnology, 2004,24(11/12):910-918.
[7]HUANG T, ZHANG X M, DING H. Decoupled Chip Thickness Calculation Model for Cutting Force Prediction in Five-axis Ball-end Milling[J]. International Journal of Advanced Manufacturing Tecnology, 2013,69：1203-1217.
[8]RAO V S, RAO P V M. Modelling of Tooth Trajectory and Process Geometry in Peripheral Milling of Curved Surfaces[J]. International Journal of Machine Tools and Manufacture, 2005, 45(6):617-630.
[9]SUN Y W, REN F, GUO D M, et al. Estimation and Experimental Validation of Cutting Forces in Ball-end Milling of Sculptured Surfaces[J]. International Journal of Machine Tools and Manufacture, 2009, 49(15)：1238-1244.
[10]GUO D M, REN F, SUN Y W. An Approach to Modeling Cutting Forces in Five-axis Ball-end Milling of Curved Geometries Based on Tool Motion Analysis[J]. Journal of Manufacturing Science and Engineering, 2010, 132(4):041004.
[11]SUN Y W, GUO D M. Numerical Simulation and Prediction of Cutting Forcer in Five-axis Milling Processes with Cutter Run-out[J]. International Journal of Machine Tools and Manufacture, 2011, 51(10/11)：806-815.
[12]LIANG X G, YAO Z Q. An Accurcy Algorithm for Chip Thickness Modeling in 5-axis Ball Finsh Milling[J]. Computer-Aided Design, 2011, 43(8)：971-978.
[13]MUKHERJEE N P, RAVI B. An Integrated Framework for Die and Mold Cost Estimation Using Design Features and Tooling Parameters[J]. International Journal of Advanced Manufacturing Technology, 2005, 26：1138-1149.
[14]ZHANG X W, YU T B, WANG W. S. Dynamic Cutting Force Prediction for Micro End Milling Considering Tool Vibrations and Run-out[J]. Journal of Mechanical Engineering Science, 2019, 233(7)：2248-2261.
[15]LI S J, ZHOU Y F, JIN R C. Dynamic Force Modelling for a Ball-end Milling Cutter Based on the Merchant Oblique Cutting Theory[J]. International Journal of Machine Tools and Manufacture, 2001, 17：477-483.
[16]LIU X W, CHENG K, LONGSTAFF A P, et al. Improved Dynamic Cutting Force Model in Ball-end Milling, PartⅠ：Theoretical Modelling and Experiental Calibration[J]. International Journal of Advanced Manufacturing Tecnology, 2005, 26(5)：

457-465.
[17]INSPERGER T G, STEPAN P V， BAYLY B P, et al.Multiple Chatter Frequencies in Milling Processes[J]. Journal of Sound and Vibration, 2003, 262(2)：333-345.
[18]王扬渝，计时鸣，王慧强，等. 球头铣削多硬度拼接淬硬钢的振动研究[J].中国机械工程, 2012，23（6）：636-641.
WANG Yangyu, JI Shiming, WANG Huiqiang, et al. Investigation on Vibration of Ball End Milling Harden Steel Assembled with Different Hardness[J]. China Mechanical Engineering, 2012，23（6）：636-641.