坐标系导引下的线缆布线点位对应关系自动提取方法

doi:10.3969/j.issn.1004-132X.2020.14.010

中国机械工程 ›› 2020, Vol. 31 ›› Issue (14): 1708-1716.DOI: 10.3969/j.issn.1004-132X.2020.14.010

坐标系导引下的线缆布线点位对应关系自动提取方法

王发麟¹, 郭学鹏², 李志农¹, 宋利康³

1. 南昌航空大学无损检测技术教育部重点实验室, 南昌, 330063;
2. 南昌航空大学航空制造工程学院, 南昌, 330063;
3. 江西洪都航空工业集团有限责任公司, 南昌, 330024

收稿日期:2019-10-31 出版日期:2020-07-25 发布日期:2020-08-26
作者简介:王发麟,男,1986年生,讲师、博士。研究方向为数字化设计制造技术、航空航天产品柔性线缆敷设与仿真技术等。发表论文20余篇。E-mail:wj54nh@sina.com。
基金资助:
国家自然科学基金资助项目（51675258）；机械系统与振动国家重点实验室开放基金课题（MSV201914）；江西省教育厅科学技术研究项目（GJJ180539）；南昌航空大学博士科研启动基金资助项目（EA201803301）

Automatic Extraction Method for Corresponding Relationship among Endpoint-to-location of Cable Wiring under Coordinate System Guidance

WANG Falin¹, GUO Xuepeng², LI Zhinong¹, SONG Likang³

1. Key Laboratory of Nondestructive Testing, Ministry of Education, Nanchang Hangkong University, Nanchang, 330063;
2. School of Aeronautical Manufacturing Engineering, Nanchang Hangkong University, Nanchang, 330063;
3. Jiangxi Hongdu Aviation Industry Group Limited Liability Company, Nanchang, 330024

Received:2019-10-31 Online:2020-07-25 Published:2020-08-26

摘要/Abstract

摘要： 针对复杂机电产品人工寻找线缆端点与电连接器各接线位置之间的点位对应关系效率低、易出错等问题，提出了一种坐标系导引下的线缆布线点位对应关系自动提取方法。建立了基于线缆布线工艺规划的线缆信息模型和电连接器信息模型，采用特征提取技术提取线缆信息和电连接器信息；分别建立了线缆端点坐标系和电连接器各点位坐标系，运用坐标转换将两坐标系变换到装配坐标系下并分析各坐标系之间的关系，在坐标系导引下自动提取线缆与电连接器之间的点位对应关系。将该方法应用于某型相控阵雷达装配体的线缆布线中，实例证明，该方法能快速且准确地提取线缆端点与电连接器各接线位置之间的点位对应关系。

关键词: 坐标系导引, 点位对应关系, 线缆布线, 自动提取, 坐标转换

Abstract: To solve the problems of the low efficiency and error-prone of manual search for the corresponding relationship of endpoint-to-location among cable endpoints and electrical connector's wiring positions in complex mechatronic products, an automatic extraction method of corresponding relationship among endpoint-to-location of cable wiring was proposed based on coordinate system guidance. Firstly, a cable information model and electrical connector information model were established based on cable wiring process planning, and the cable information and the electrical connector information were extracted by the feature extraction technology. Then the endpoint coordinate system of cable and the point coordinate system of electrical connectors were established, the relationships were analyzed after transform the two coordinate systems into the assembly coordinate system by coordinate transformation, thus the corresponding relationship of endpoint-to-location among the cables and the electrical connectors were automatically extracted based on coordinate system guidance. Finally, the method was applied to the automatic extraction of corresponding relationship among endpoint-to-location of cable wiring of phased array radar. The examples prove that the corresponding relationship of endpoint-to-location among the cable endpoints and the electrical connector's wiring positions are extracted quickly and accurately by the proposed method.

Key words: coordinate system guidance, corresponding relationship of endpoint-to-location, cable wiring, automatic extraction, coordinate transformation

中图分类号:

TP391

王发麟, 郭学鹏, 李志农, 宋利康. 坐标系导引下的线缆布线点位对应关系自动提取方法[J]. 中国机械工程, 2020, 31(14): 1708-1716.

WANG Falin, GUO Xuepeng, LI Zhinong, SONG Likang. Automatic Extraction Method for Corresponding Relationship among Endpoint-to-location of Cable Wiring under Coordinate System Guidance[J]. China Mechanical Engineering, 2020, 31(14): 1708-1716.

参考文献

[1] 宁汝新, 刘检华, 唐承统, 等. 虚拟装配技术及其应用[J]. 国防制造技术, 2009, 4(2):22-29. NING Ruxin, LIU Jianhua, TANG Chengtong, et al. Virtual Assembly Technology and Its Application[J]. Defense Manufacturing Technology, 2009, 4(2):22-29.
[2] 宁汝新, 郑轶. 虚拟装配技术的研究进展及发展趋势分析[J]. 中国机械工程, 2005,16(15):1398-1404. NING Ruxin, ZHENG Yi. Analysis on Recent Study Progresses and Trends of Virtual Assembly Technology[J].China Mechanical Engineering, 2005, 16(15):1398-1404.
[3] CONRU A B. A Genetic Approach to the Cable Harness Routing Problem[C]//Proceedings of the 1st IEEE Conference on Computational Intelligence. Washington D C, 1994:200-205.
[4] HERGENRÖTHER E, DHNE P, RUNDETURMSTR R. Real-time Virtual Cables Based on Kinematic Simulation[C]//Proceedings of the WSCG2000. Pilzěn, 2000:402-409.
[5] 魏发远, 陈新发, 王峰军. 电缆虚拟布线及其逆运动学仿真[J]. 计算机辅助设计与图形学学报, 2006,18(10):1623-1627. WEI Fayuan, CHEN Xinfa, WANF Fengjun. Virtual Wiring and Simulation of Cable Layout with Inverse Kinematics[J]. Journal of Computer-Aided Design & Computer Graphics, 2006, 18(10):1623-1627.
[6] 王发麟, 廖文和, 郭宇, 等. 复杂机电产品线缆信息本体表达与存储分析[J]. 图学学报, 2015,36(3):376-383. WANG Falin, LIAO Wenhe, GUO Yu, et al. Stored Analysis and Ontology Expression of Cable Harness Information for Complex Mechatronic Products[J]. Journal of Graphics, 2015, 36(3):376-383.
[7] 王金芳, 闫静, 武凯, 等. 基于Pro/E的线缆装配工艺规划系统关键技术研究[J]. 中国机械工程, 2008,19(13):1565-1569. WANG Jinfang, YAN Jing, WU Kai, et al. Key Technologies on the Cable Harness Assembly Planning System Based on Pro/E[J]. China Mechanical Engineering, 2008, 19(13):1565-1569.
[8] 刘佳顺, 刘检华, 王志斌, 等. 虚拟环境下复杂线缆的集成信息模型[J]. 计算机集成制造系统, 2013,19(5):964-971. LIU Jiashun, LIU Jianhua, WANG Zhibin, et al. Integrated Information Model of Complex Cable Harness in Virtual Environment[J].Computer Integrated Manufacturing Systems,2013,19(5):964-971.
[9] 尚炜, 宁汝新, 刘检华, 等. 一种以拓扑结构信息为骨架的线缆数字化模型[J]. 计算机集成制造系统, 2012,18(12):2588-2594. SHANG Wei, NING Ruxin, LIU Jianhua, et al. Cable Harness Digital Model with Topology as Its Skeleton[J].Computer Integrated Manufacturing Systems, 2012, 18(12):2588-2594.
[10] 郭伟, 刘艳芳, 赵辉, 等. 基于骨架模型的快速布线方法[J]. 计算机集成制造系统, 2012,18(11):2391-2397. GUO Wei, LIU Yanfang, ZHAO Hui, et al. Fast Wiring Method Based on Skeleton Model[J].Computer Integrated Manufacturing Systems, 2012, 18(11):2391-2397.
[11] ERIKSSON H E, PENKER M. Business Modeling with UML:Business Patterns at Work[M]. New York:Wiley Computer Publishing, 1998.
[12] 付高嵩, 陶友传. 舰载电子设备电缆布线设计规范及其表达方法[J]. 计算机工程与科学, 2001,23(4):72-75. FU Gaosong, TAO Youchuan. Design Specifications and Expression Methods for Cable Wiring of Shipboard Electronic Equipment[J]. Computer Engineering and Science, 2001, 23(4):72-75.
[13] 姜康, 马世纪. 基于改进A^*算法的线缆路径规划方法[J]. 中国机械工程, 2019,30(6):699-708. JIANG Kang, MA Shiji. A Cable Path Planning Method Based on Improved A^* Algorithm[J]. China Mechanical Engineering, 2019, 30(6):699-708.
[14] 朱永国, 张文博, 刘春锋, 等. 基于SDT和间接平差的中机身自动调姿精度分析[J]. 航空学报, 2017,38(12):296-309. ZHU Yongguo, ZHANG Wenbo, LIU Chunfeng, et al. Accuracy Analysis for Automatical Adjustment of Aircraft Fuselage Posture Based on SDT and Indirect Adjustment[J]. Acta Aeronautica et Astronautica Sinica, 2017, 38(12):296-309.

坐标系导引下的线缆布线点位对应关系自动提取方法

Automatic Extraction Method for Corresponding Relationship among Endpoint-to-location of Cable Wiring under Coordinate System Guidance

RichHTML

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 3

编辑推荐

Metrics

[1]	朱月1;鄢萍1;李先广2. 盘类齿轮成形磨齿自适应加工研究[J]. 中国机械工程, 2018, 29(09): 1055-1062.
[2]	陈雷, 邓明然, 江征风, 罗亚波. 基于坐标投影的钢桥螺栓与零件BOM自动生成方法研究[J]. 中国机械工程, 2012, 23(20): 2469-2476.
[3]	程维明, 宋伟, 刘亮, 孙桂清, 刘恩频. 一种新型桥门式起重机轨道测量方法 [J]. 中国机械工程, 2010, 21(18): 2187-2191.