Research on Complementary Double-layer Time-grid Angular Displacement Sensor

doi:10.3969/j.issn.1004-132X.2023.04.007

Abstract

Abstract: Aiming at the problems of the small amplitude of the induction signals and the low utilization rate of the uniform effective area of the time-varying magnetic field of the double-layer time-grid angular displacement sensors developed in the early stage， a double-layer complementary time-grid angular displacement sensor was proposed based on the original “figure-eight” half-sine structure. According to the characteristics of the double-layer time-grid displacement sensors， the spatial magnetic field distribution models were established， and the advantages of the complementary structure of the double-layer time-grid angular displacement sensors in forming traveling waves were verified. According to the magnetic field distribution of the excitation coil， the space between the double-layer planar excitation coil under this parameter state was as 0.235 mm. Finally， finite element simulation analysis and experimental verification were carried out. The simulation results show that the complementary structure may effectively increase the induction signal intensity， the peak-to-peak values of the short-period errors are significantly reduced， which may effectively suppress the 1st harmonic and the 4th harmonic in the angle errors. The experimental data shows that the original short-period error of the sensors is （-13.61″， 13.30″）， and the corrected error is （-3.01″， 0.78″）； the original long-period error of the sensor is （-19.60″， 21.96″）， and the corrected error is （-2.62″， 3.30″）， which reduces the primary errors by 66.3% compared to the single-layer “U”-shaped structure， the 4th time error is reduced by 25.3%.

Key words: , angular displacement sensor, time grid, double layer, induction intensity, error

摘要： 针对当前研制的双层时栅角位移传感器感应信号幅值小、时变磁场的均匀有效面积利用率低等问题，在原有“八”字形半正弦结构的基础上提出了一种双层互补式时栅角位移传感器设计方案。根据双层时栅位移传感器的特点，建立了其空间磁场分布模型，验证了双层时栅角位移传感器的互补式结构在构成行波上的优势；根据激励线圈的磁场分布规律进行建模，得到该参数状态下双层平面激励线圈的间距为0.235 mm。最后进行了有限元仿真分析和实验验证。仿真分析表明：采用互补式结构能有效增大感应信号强度，传感器的短周期误差峰峰值显著降低，能够有效抑制角度误差中的1次谐波和4次谐波。实验数据表明：传感器短周期原始误差为（-13.61″，13.30″），修正后误差为（-3.01″，0.78″）；传感器长周期原始误差为（-19.60″，21.96″），修正后误差为（-2.62″，3.30″）；相比单层“U”字形结构，1次误差减小了66.3%，4次误差减小了25.3%。

关键词: 角位移传感器, 时栅, 双层, 感应强度, 误差

CLC Number:

YANG Jisen, FU Hang, QIN Ziyang, ZHOU Run. Research on Complementary Double-layer Time-grid Angular Displacement Sensor[J]. China Mechanical Engineering, 2023, 34(04): 431-439.

杨继森, 付航, 秦梓洋, 周润. 互补式双层时栅角位移传感器研究[J]. 中国机械工程, 2023, 34(04): 431-439.

References

［1］刘小康，柳康，蒲红吉，等. 基于二次调制的高精度多圈绝对式时栅角位移传感器［J］. 仪器仪表学报， 2021， 42（5）：90-98.
LIU Xiaokang， LIU Kang， PU Hongji， et al. High Precision Multi-turn Absolute Time Grating Angular Displacement Sensor Based on Secondary Modulation［J］. Chinese Journal of Scientific Instrument， 2021， 42（5）：90-98.
［2］LIU X， ZHAN B， YU Z， et al. A Miniaturized Capacitive Absolute Angular Positioning Sensor Based on a Dual Two-stage Secondary Re-modulation Scheme with Time-division Multiplexing［J］. Sensors and Actuators A Physical， 2020， 310：112043.
［3］杨继森，牟智铭，李路建，等. 差动结构的平面二维时栅位移传感器［J］. 中国机械工程， 2020， 31（12）：1444-1451.
YANG Jisen， MOU Zhiming， LI Lujian， et al. Planar Two-dimensional Time-grid Displacement Sensor with Differential Structure［J］. China Mechanical Engineering， 2020， 31（12）：1444-1451.
［4］柯庆镝，李杰，吕岩，等. 基于结构和性能相似度分析函数的机械产品优化设计方法［J］. 中国机械工程， 2019（5）：586-594.
KE Qingdi， LI Jie， LYU Yan， et al. Optimization Design Method of Mechanical Products Based on Structure and Performance Similarity Analysis Function［J］. China Mechanical Engineering， 2019（5）：586-594.
［5］PENG D， LIU X， MIN F， et al. Time Grating Linear Displacement Sensor Based on Alternating Light Field：CN20141090968［P］. 2014-11-13.
［6］陈慧涛，常思勤，范爱民. 发动机电磁驱动配气机构性能试验［J］. 中国机械工程， 2019， 30（1）：2-8.
CHEN Huitao， CHANG Siqin， FAN Aimin. Performance Test of Electromagnetic Drive Valve Mechanism for Engine［J］. China Mechanical Engineering， 2019， 30（1）：2-8.
［7］倪玉吉，王明娣，陈添禹，等. 磁阻式电磁蓄能无针注射系统的设计与实验研究［J］. 中国机械工程， 2021， 32（2）：227-234.
NI Yuji， WANG Mingdi， CHEN Tianyu， et al. Design and Experimental Study of Magnetic Reluctance Electromagnetic Energy Storage Needle-free Injection System［J］. China Mechanical Engineering， 2021， 32（2）：227-234.
［8］武亮，彭东林，鲁进，等. 基于平面线圈线阵的直线时栅位移传感器［J］. 仪器仪表学报， 2017， 38（1）：83-90.
WU Liang, PENG Dongling, LU Jin, et al.Linear Time Grating Displacement Sensor Based on Linear Array of Planar Coils［J］.Chinese Journal of Scientific Instrument,2017, 38(1): 83-90.
［9］CHEN Z， PENG D， YONG Z， et al. The Research and Design of Transmission Error Measurement System Based on an Absolute Displacement Sensor-time Grating［C］∥Proceedings International Conference on Electrical and Control Engineering. Washington DC，2010, 2404-2406.
［10］彭东林，张兴红，刘小康，等. 场式时栅位移传感器研究［J］. 仪器仪表学报， 2003， 24（3）：321-323.
PENG Donglin， ZHANG Xinghong， LIU Xiaokang， et al. Research on Field-type Time-grid Displacement Sensor［J］. Chinese Journal of Scientific Instrument， 2003， 24（3）：321-323.
［11］姚有光，陈鸣. 基于等效磁网络模型的凸极同步电机电磁计算［J］. 中小型电机， 1996， 23（6）：7-11.
YAO Youguang， CHEN Ming. Electromagnetic Calculation of Salient Pole Synchronous Motor Based on Equivalent Magnetic Network Model［J］. Small and Medium Electric Machines 1996， 23（6）：7-11.
［12］鲁进，陈锡侯，武亮，等. 基于平面线圈的高分辨力时栅角位移传感器［J］. 光学精密工程， 2017， 25（1）：172-181.
LU Jin， CHEN Xihou， WU Liang， et al. High Resolution Time Grid Angular Displacement Sensor Based on Planar Coil［J］. Optics and Precision Engineering， 2017， 25（1）：172-181.
［13］王秉中. 计算电磁学［M］. 北京：科学出版社， 2002.
WANG Bingzhong. Computational Electromagnetism［M］. Beijing：Science Press， 2002.
［14］陆善婷，杨敏红. 基于峰值采样圆感应同步器测角系统研究［J］. 电子测量技术， 2018， 41（1）：105-108.
LU Shanting， YANG Minhong. Angular Measurement System Based on Peak Sampling Circle Induction Synchronizer［J］. Electronic Measurement Technology， 2018， 41（1）：105-108.
［15］殷晓康，李盈盈，张晓瑞，等. 基于平面线圈电容电感效应的双模式检测技术［J］. 机械工程学报， 2021， 57（14）：168-176.
YIN Xiaokang， LI Yingying， ZHANG Xiaorui， et al. Dual-mode Detection Based on Planar Coil Capacitance Inductance Effect［J］. Journal of Mechanical Engineering， 2021， 57（14）：168-176.

[1]	LI Xiao-Li, CHEN Wei, YAN Rong. Adaptive Compensation of Contour Errors Based on BP Neural Networks [J]. J4, 201016, 21(16): 1902-1906.
[2]	QIAO Guan, CHEN Jiaqi, TANG Shufeng, LIU Guoqiang, LIU Geng. A Review of Thermal Characteristics for Planetary Roller Screw Mechanisms [J]. China Mechanical Engineering, 2026, 37(1): 162-173.
[3]	YANG Mingxing, SHEN Jiale, GAO Peng, ZHANG Xing, WANG Junxiang. Design of Continuum Robots and Compensation Strategies for Losses of Guide Paths [J]. China Mechanical Engineering, 2025, 36(12): 2820-2828.
[4]	DAI Xin, LIU Huanlao, WANG Yulin, LI Xiang. A Key Geometric Error Identification Method for CNC Machine Tools Based on Machining Trajectory Sensitivity Indicators [J]. China Mechanical Engineering, 2025, 36(12): 2862-2869.
[5]	Xiang LI, Huanlao LIU, Yulin WANG, Xin DAI. An Identification Method of PIGEs for Rotary Axes of Five-axis Machine Tools [J]. China Mechanical Engineering, 2025, 36(11): 2609-2617.
[6]	Xiaokai WANG, Gefei ZHENG, Kangwen HUANG, Ziqiang LIU, Xinghui HAN, Lin HUA. Staged Measurement Model and Method for Geometric Shape of Super Large Ring Forging Processes Based on Multi-source Information Fusion [J]. China Mechanical Engineering, 2025, 36(11): 2747-2756.
[7]	Wenhua SHEN, Xibin WANG, Yonghao QIAN, Zhibing LIU, Ci SONG. Research on Online Measurement and Evaluation of Axial Straightness Errors for Deep-hole Parts [J]. China Mechanical Engineering, 2025, 36(09): 2011-2021.
[8]	Mingfan LI, Long YANG, Sheng LI, Huan GUO, Guoqiang FU. Thermal Image Input-based ResNet Method for Thermal Error Modeling of Machine Tool Spindles [J]. China Mechanical Engineering, 2025, 36(09): 2057-2067.
[9]	Siqi LIU, Peitang WEI, Rui HU, Xuesong DU, Li LUO, Caichao ZHU, Pengliang ZHOU. Statistical Analysis of Planetary Roller Screw Thread Machining Errors and Comparative Study at Home and Abroad [J]. China Mechanical Engineering, 2025, 36(08): 1713-1727.
[10]	Haitao LI, Shulei XU, Yawen WANG, Xiaobin BAI, Xiaoning JING. Research on Calibration Principle and Method of Laser Tracker Base Stations Based on External Physical Standard [J]. China Mechanical Engineering, 2025, 36(08): 1875-1882.
[11]	YUAN Jiabin, GUO Xipeng, LI Rong, YIN Shaohui. Ultra-precision Turning Alignment Error Compensation Technology in Multi-axis Simultaneous Operations [J]. China Mechanical Engineering, 2025, 36(07): 1397-1406.
[12]	ZHENG Chao, LIU Jianchao, WU JunXUE Xin. Vibration Reduction Analysis of All-metal Multi-directional Isolation Devices [J]. China Mechanical Engineering, 2025, 36(07): 1463-1470.
[13]	ZHAO Tingqi1, CHENG Hongyu2, SUN Maokai1, WANG Shenghai1, WANG Haoran1, CHEN Haiquan1. Nonlinear Stability Control of Multi-cable Anti-sway Systems for Marine Cranes [J]. China Mechanical Engineering, 2025, 36(07): 1487-1496.
[14]	ZHANG Jianyu, WANG Liuzhen, XIAO Yong, MA Yanan. Fusion of Degradation Feature Information and Remaining Life Prediction for Rolling Bearings [J]. China Mechanical Engineering, 2025, 36(07): 1553-1561.
[15]	. Geometric Feature Modeling and Assembly Interference Detection Method for Large Ship Components [J]. China Mechanical Engineering, 2025, 36(07): 1636-1649.