小型无人机气动肌腱式弹射系统动态仿真与优化

摘要/Abstract

摘要： 针对冲击气缸式无人机弹射系统耗气量高、质量大、动态特性差等弊端，提出了一种仿生气动肌腱式无人机弹射系统，利用气动肌腱的弱非线性，通过配置楔角以改善无人机加速阶段的受力情况，减缓加速度波动。对该弹射系统进行数学建模和动力学分析，并搭建Simulink模型对该系统进行仿真求解；通过MATLAB与Simulink对现有加速轨道通过多目标遗传算法实现进一步优化。优化后的加速轨道能提升加速度均值、气动肌腱能量利用率和起飞速度，且降低了加速度峰值，加速度波动在原有基础上降低了76.79%。仿真和优化结果表明，提出的气动肌腱式无人机弹射系统不仅避免了冲击气缸式弹射系统的缺点，还能进一步平缓加速度，减小整体系统的最大过载。

关键词: 无人机, 气动肌腱, 弹射, 仿生

Abstract: Aiming at the disadvantages of high impact, large mass and poor dynamic characteristics of impact cylinder UAV ejection system, a bionic pneumatic muscle driven UAV ejection system was proposed. By the method of utilizing the small nonlinearity of pneumatic tendons and configuring the wedge angles, the project may ameliorate the stress conditions of the UAVs and slow down the acceleration fluctuation. The mathematical modeling and dynamic analysis of the ejection system were carried out, and the Simulink model was built to emulate the system. Combing the MATLAB and Simulink, the existing acceleration trajectories were further optimized by multi-objective genetic algorithm. The optimized acceleration track may improve the acceleration mean, the energy utilization rate of the pneumatic muscle and the take-off speed. At the same time, the acceleration peak values are reduced, and the acceleration fluctuations are reduced by 76.79% on the original basis. Simulation and optimization results show that the system may avoid the disadvantages of impact cylinder ejection system, and make the acceleration changes smoothly and reduce the maximum overload of the whole systems.

Key words: unmanned aerial vehicle (UAV), pneumatic tendon, ejection, bionic

中图分类号:

V279
TH139

黄国勤1, 2;罗莎祁1, 2;于今1, 2. 小型无人机气动肌腱式弹射系统动态仿真与优化[J]. 中国机械工程.

HUANG Guoqin1, 2;LUO Shaqi1, 2;YU Jin1, 2. Dynamic Simulation and Optimization of Pneumatic Tendon Ejection Systems for Small UAVs[J]. China Mechanical Engineering.

参考文献

[1]余晓军, 高翔, 钟民军. 蒸汽弹射器的动力学仿真研究[J]. 船海工程, 2005(3): 1-4.
YU Xiaojun, GAO Xiang, ZHONG Minjun. Simulation on Dynamics of the Steam Powered Catapult[J]. Ship & Ocean Engineering, 2005(3): 1-4.
[2]黄钰曌. 高速液压弹射系统设计及关键元件研究[D]. 杭州：浙江工业大学, 2012.
HUANG Yuzhao. Designing of High Speed Hydraulic Ejection System and Investigation of the Key Component[D]. Hangzhou: Zhejiang University of Technology, 2012.
[3]刘兰荣, 马笑尘. 无人机液压弹射器弹射过程的仿真分析与试验研究[J]. 液压与气动, 2016(5): 65-68.
LIU Lanrong, MA Xiaochen. Simulation Analysis and Experimental Research of UAV Hydraulic Catapult Ejection Process[J]. Chinese Hydraulics & Pneumatics, 2016(5): 65-68.
[4]张明元, 马伟明, 汪光森,等. 飞机电磁弹射系统发展综述[J]. 舰船科学技术, 2013, 35(10): 1-5.
ZHANG Mingyuan, MA Weiming, WANG Guangsen, et al. Overview on a Significant Technology of Modern Aircraft Carrier-electromagnetic Aircraft Launch System[J]. Ship Science and Technology,2013, 35(10):1-5.
[5]卢伟, 马晓平, 周明,等. 无人机气动弹射动力学仿真与优化[J]. 西北工业大学学报, 2014(6): 865-871.
LU Wei, MA Xiaoping, ZHOU Ming, et al. Dynamic Simulation and Optimization of UAV Pneumatic Launching[J]. Journal of Northwestern Polytechnical University, 2014(6):865-871.
[6]赵灼辉, 吴素珍. 无人机液压弹射系统的模型研究与仿真[J]. 机床与液压，2014(22):130-132.
ZHAO Zhuohui, WU Suzhen. Research and Simulation to the Model of UAV Hydraulic Launch System[J]. Machine Tool & Hydraulics, 2014(22):130-132.
[7]SIDDIQUI B A, RAHMAN H U, KUMAR C, et al. Computer Aided Modeling and Simulation of Pneumatic UAV Catapult Mechanism[C]// International Mechanical Engineering Congress. Karachi, Pakistan, 2017:863-869.
[8]李悦, 裴锦华. 无人机气液压发射动力学数值仿真[J]. 机械工程学报, 2011, 47(8): 183-190.
LI Yue, PEI Jinhua. Dynamic Numerical Simulation of the Pneumatic and Hydraulic Launching of UAV[J]. Journal of Mechanical Engineering, 2011, 47(8): 183-190.
[9]REPPERGER D W, JOHNSON K R, PHILIPS C A. Nonlinear Feedback Controller Design of a Pneumatic Muscle Actuator System[C]//American Control Conference. San Diego,1999: 1525-1529.
[10]杨风波, 马大为, 朱忠领, 等. 基于真实热力学过程分析的气动弹射性能研究[J]. 机械工程学报, 2013, 49(24): 167-174.
YANG Fengbo, MA Dawei, ZHU Zhongling, et al. Pneumatic Catapult Performance Research Based on the True Thermodynamic Process Analysis[J]. Journal of Mechanical Engineering, 2013, 49(24): 167-174.
[11]郑安宾, 金健, 李增书. McKibben气动肌肉数学模型的发展[J]. 液压气动与密封, 2010, 30(12): 5-8.
ZHENG Anbin, JIN Jian, LI Zengshu. McKibben Pneumatic Muscle Mathematical Modeling Development[J]. Hydraulic Pneumatic & Seals, 2010, 30(12): 5-8.
[12]卫玉芬, 李小宁. 气动肌肉的驱动特性研究[J]. 液压与气动, 2004(7): 24-26.
WEI Yufen, LI Xiaoning. Study on Actuating Characteristics of Pneumatic Muscle[J]. Chinese Hydraulics & Pneumatics, 2004(7): 24-26.
[13]李醒飞, 郑奇, 张国雄. 类人气动肌肉模型与实验研究[J]. 天津大学学报(自然科学与工程技术版), 2005, 38(3): 242-247.
LI Xingfei, ZHENG Qi, ZHANG Guoxiong. Mathematic Model and Experimental Study of Humanoid Pneumatic Muscle[J]. Journal of Tianjin University(Science and Technology) , 2005, 38(3): 242-247.
[14]CHOU C P, HANNAFORD B. Measurement and Modeling of McKibben Pneumatic Artificial Muscles[J]. IEEE Transactions on Robotics & Automation, 2006, 12(1): 90-102.
[15]高永, 孟浩, 李冰,等. 基于Simulink的小型无人机弹射架性能仿真[J]. 海军航空工程学院学报, 2017(5): 452-456.
GAO Yong, MENG Hao, LI Bing, et al. Performance Simulation of Small UAV Ejection Frame Based on Simulink[J]. Journal of Naval Aeronautical and Astronautical University, 2017(5): 452-456.
[16]DICKARD H E. Mini-RPV Launch System Conceptual Study[R]. ADA062990, 1978.