基于附加约束的小型涡轮增压器转子模态测试

摘要/Abstract

摘要： 针对转子模态参数难以有效获取的问题，进行了基于附加约束的小型涡轮增压器转子模态测试研究。以多种材料和零部件组成的某型汽油发动机涡轮增压器转子结构为例，采用有限元法构建了其有限元模型，得到自由边界条件下转子前三阶模态频率。然后分别采用卧式悬挂、立式悬挂、海绵垫、硬纸垫四种不同附加约束条件，开展转子的力锤模态测试，通过稳态图识别模态频率，与有限元仿真结果进行对比发现，采用悬挂方式较采用直接固定约束方式的识别值要低，而采用立式悬挂约束方式获得的转子模态测试综合效果最佳。

关键词: 模态参数, 附加约束, 涡轮增压器转子, 锤击模态测试, 稳态图

Abstract: As modal parameters usually were difficult to obtain for small-size turbocharger rotors, a rotor modal testing with additional constraints was proposed. A gasoline engine turbocharger rotor including multi materials and components was used as the example to demonstrate the proposed approach. A finite element (FE) model for turbocharger rotor with free boundary conditions was built to calculate the modal frequencies for the former three orders. Then impact modal testing was carried out based on four different additional constraints including horizontal hanging, vertical hanging, supporting on spongy cushion, and supporting on hardboard. The modal frequencies were evaluated from the stability diagrams. It is found the recognition values from constraint way of hanging are lower than that of the constraint way of supporting compared to the FE simulation. However, the modal frequencies identified under the vertical hanging constraint is the best for all kinds of constraints.

Key words: modal parameter, additional constraint, turbocharger rotor, hammer impact testing, stability diagram

中图分类号:

宾光富, 周伟, 王钢, 陈文. 基于附加约束的小型涡轮增压器转子模态测试[J]. 中国机械工程.

BIN GuangfuZHOU WeiWANG GangCHEN Wen. Modal Testing for Small-size Turbocharger Rotor with Additional Constraints[J]. China Mechanical Engineering.

参考文献

[1]KIRK R G. Experimental Evaluation of Hydrodynamic Bearings for a High Speed Turbocharger[J]. Journal of Engineering for Gas Turbines and Power，2014，136(7)：072501.

[2]李红伟，于文涛，刘淑琴. 基于ANSYS的磁悬浮挠性转子模态分析与设计[J]. 中国机械工程，2014，25(11)：1447-1452.
LI Hongwei，YU Wentao，LIU Shuqin. Mode Analysis and Design of Maglev Flexible Rotor with ANSYS[J]. China Mechanical Engineering，2014，25(11)：1447-1452.

[3]WANG Longkai, BIN Guangfu, LI Xuejun, et al. Effects of Unbalance Location on Dynamic Characteristics of High-speed Gasoline Engine Turbocharger with Floating Ring Bearings[J]. Chinese Journal of Mechanical Engineering, 2016, 29(2):271-280.

[4]应广驰，孟光，龙新华，等. 用自由界面模态综合法研究发动机-排气管-涡轮增压器系统的振动[J]. 机械强度，2010，32(1)：10-16.
YING Guangchi，MENG Guang，LONG Xinhua，et al. Study on Engine Manifold Turbocharger System's Vibration by Free Interface Modal Synthesis Method[J]. Journal of Mechanical Strength，2010，32(1)：10-16.

[5]罗君杰，龙新华，孟光. 基于实验模态分析的涡轮增压器压缩端振动响应分析[J]. 噪声与振动控制，2010，30(5)：10-14.
LUO Junjie，LONG Xinhua，MENG Guang. Vibration Response Analysis of Turbocharger Compressor Housing Based on Experimental Modal Analysis[J]. Noise and Vibration Control，2010，30(5)：10-14.

[6]董小瑞，杨世文. 复杂结构模态测试方法研究[J]. 兵工学报，2008，29(4)：474-477.
DONG Xiaorui，YANG Shiwen. Research on Modal Measurement Method of Complicated Structure[J]. Acta Armamentarii, 2008，29(4)：474-477.

[7]罗忠，王宇，孙宁，等. 不同边界条件下旋转薄壁短圆柱壳的强迫振动响应计算[J]. 机械工程学报，2015，51(9)：64-70.
LUO Zhong，WANG Yu，SUN Ning，et al. Forced Vibration Response Calculation of Rotating Short Thin Cylindrical Shells for Various Boundary Conditions[J]. Journal of Mechanical Engineering，2015，51(9)：64-70.

[8]任军，毕树生. 模态测试中力传感器附加质量辨识及消除方法研究[J]. 振动与冲击，2014，33(14): 108-112.
REN Jun，BI Shusheng. Identification and Correction of Force Transducer Mass Effects in Modal Testing[J]. Journal of Vibration and Shock，2014，33(14)：108-112.

[9]林贤坤，覃柏英，张令弥，等. 基于附加质量的试验模态振型质量归一化[J]. 振动、测试与诊断, 2012,32(5):784-790.
LIN Xiankun，QIN Boying，ZHANG Lingmi，et al. Way of Getting Mass-normalized Experimental Mode Shapes Based on Mass Changes[J]. Journal of Vibration, Measurement & Diagnosis,2012,32(5):784-790.

[10]赵俊，聂振华，马宏伟. 拱结构模态测试中传感器优化配置[J]. 振动、测试与诊断，2011，31(2)：217-222.
ZHAO Jun，NIE Zhenhuai，MA Hongwei. Sensor Placement Optimization for Modal Test of Arch Structure[J]. Journal of Vibration Measurement & Diagnosis，2011，31(2)：217-222.

[11]蔡力钢，马仕明，赵永胜，等. 多约束状态下重载机械式主轴有限元建模及模态分析[J]. 机械工程学报, 2012,48(3):165-173.
CAI Ligang，MA Shiming，ZHAO Yongsheng，et al. Finite Element Modeling and Modal Analysis of Heavy-duty Mechanical Spindle under Multiple Boundary conditions[J]. Journal of Mechanical Engineering，2012，48(3)：165-173.

[12]程小勇，陈果，刘明华，等. 初始安装应力对管道固有频率的影响分析及试验验证[J]. 中国机械工程，2015，26(4)：512-517.
CHENG Xiaoyong，CHEN Guo，LIU Minghua，et al. Analysis and Experimental Verification to Effects of Pipe Initial Installation Stress on Pipe’s Natural Frequencies[J]. China Mechanical Engineering，2015，26(4)：512-517.

[13]李元生，李磊，敖良波，等. 涡轮增压器转子系统三维动力学特性分析[J]. 机械强度，2011，33(2)：175-178.
LI Yuansheng，LI Lei，AO Liangbo，et al. Analysis of the Three-dimensional Rotor Dynamics Characteristic of the Turbocharger[J]. Journal of Mechanical Strength，2011，33(2)：175-178.

[14]MA Hui，LI Hui，NIU Heqiang，et al. Numerical and Experimental Analysis of the First and Second-mode Instability in a Rotor-bearing System[J]. Archive of Applied Mechanics，2014，84(4)：519-541.