聚合物气体辅助挤出中气体流动对熔体截面的影响

中国机械工程

聚合物气体辅助挤出中气体流动对熔体截面的影响

黄益宾1,2;余忠1;熊爱华3;章凯1

1.上饶师范学院江西省塑料制备成型重点实验室，上饶，334001
2.南密西西比大学聚合物与高性能材料系，哈蒂斯堡，39401
3.江西农业大学工学院，南昌，330031

出版日期:2017-04-10 发布日期:2017-04-07
基金资助:
江西省青年科学基金资助项目(20122BAB216012);
国家留学基金资助项目(201308360171);
江西省2015年度百人远航工程资助项目(2015141)

Effects of Gas Flow on Melt Cross Sections in Polymer Gas-assisted Extrusion

HUANG Yibin1,2;YU Zhong1;XIONG Aihua3;ZHANG Kai1

1.Jiangxi Key Laboratory of Polymer Preparation and Processing, Shangrao Normal University, Shangrao, Jiangxi，334001
2.School of Polymer and High Performance Materials, University of Southern Mississippi, Hattiesburg, MS，39401
3.School of Engineering, Jiangxi Agricultural University, Nanchang,330031

Online:2017-04-10 Published:2017-04-07

摘要/Abstract

摘要： 将聚合物熔体和低速热空气均视作不可压流体，针对一聚苯乙烯（PS）片材的全气体辅助挤出，建立了描述其气体-熔体两相分层流动的三维有限元模型，采用黏弹应力分离法（EVSS）和非协调流线迎风法（SU）等有限元方法，利用PolyFlow求解器对气体辅助流道中气体和熔体流动进行了计算，分析了熔体截面变化的规律及原因。研究结果表明：气体辅助流道内，气体对熔体有拖曳作用；沿挤出方向，熔体速度逐渐增大，而截面积逐渐减小，都在口模出口面上达到极值，同时截面形状有微小改变；口模出口面上熔体沿挤出方向的速度随入口气体体积流率的增大而近似线性增大，熔体截面积则近似线性减小。

关键词: 气体辅助挤出, 不可压缩流体, 入口体积流率, 有限元方法

Abstract: For the fully gas-assisted extrusion of a polystyrene sheet, a 3D finite element model which described the gas-melt stratified flow was established with the polymer melt and low speed heated air both being considered as incompressible fluid. Numerical computations of the flows in gas-assisted channel were performed by PolyFlow solver with some FEMs such as elastic-viscous-split-stress method (EVSS), streamline-upwind (SU) method etc. The effect laws of gas flow on melt cross sections were analyzed. The results show that in the gas-assisted channels the melt is towed by gas layer. Along the gas-assisted channels, the melt velocity in extrusion direction increases, and the melt sectional area decreases, both with flow distance and gradually reach an extreme value at die exit. On the outlet plane, the melt velocity in extrusion direction increases, and the melt sectional area decreases, both with gas volume inflow rate and in an approximately linear way.

Key words: gas-assisted extrusion, incompressible fluid, inflow volume rate, finite element method(FEM)

中图分类号:

TQ320.66

黄益宾, 余忠, 熊爱华, 章凯. 聚合物气体辅助挤出中气体流动对熔体截面的影响[J]. 中国机械工程.

HUANG Yibin, YU Zhong, XIONG Aihua, ZHANG Kai. Effects of Gas Flow on Melt Cross Sections in Polymer Gas-assisted Extrusion[J]. China Mechanical Engineering.

参考文献

[1]LIANG R F, MACKLEY M R. The Gas-assisted Extrusion of Molten Polyethylene [J]. Journal of Rheology,2001,45(1):211-226.
[2]柳和生, 卢臣, 黄兴元. 塑料异型材气辅挤出成型实验[J]. 高分子材料科学与工程,2010,26(7):93-96.
LIU Hesheng, LU Cheng, HUANG Xingyuan. Experiment of Gas-assisted Extrusion of the Plastic Profile with an Irregular Section[J]. Polymer Materials Science& Engineering,2010,26(7):93-96.
[3]柳和生,黄兴元,周国发,等.气体辅助聚合物挤出中的二维等温粘弹流动的数值模拟[J]. 应用基础与工程科学学报,2006,14(4):514-522.
LIU Hesheng, HUANG Xingyuan, ZHOU Guofa, et al. Numerical Simulation of Two Dimensional Isothermal Viscoelastic Polymer Flow in Gas-assisted Extrusion[J]. Journal of Basic Science and Engineering,2006,14(4):514-522.
[4]黄兴元,柳和生,周国发,等.气体辅助挤出中影响气垫形成及稳定性因素分析[J].塑性工程学报,2005,12(5):101-104.
HUANG Xingyuan, LIU Hesheng, ZHOU Guofa, et al. The Influence Factors on the Set up and Stability of Gas Layer in Gas Assisted Polymer Extrusion [J]. Journal of Plasticity Engineering,2005,12(5):101-104.
[5]黄益宾.聚合物气体辅助共挤成型的理论和实验研究[D].南昌:南昌大学,2011.
HUANG Yibin. Theoretical and Experimental Study on Polymer Gas-assisted Co-extrusion[D].
Nanchang: Nanchang University,2011.
[6]彭小勇,顾炜莉,柳建祥，等.低速气体流动不可压缩性理论解析[J].南华大学学报（自然科学版）,2004,18(3):34-35.
PENG Xiaoyong, GU Weili, LIU Jianxiang, et al. A Theoretical Analysis of Incompressibility of the Low Speed Gas Flow[J]. Journal of Nanhua University (Science and Technology),2004,18(3):34-35.
[7]JONES S A. Advanced Methods for Practical Applications in Fluid Mechanics [M]. Rijeka:In Tech.,2012:71-72.
[8]柳和生, 涂志刚, 熊洪槐. 聚合物熔体粘弹性本构方程[J]. 高分子材料科学与工程,2002,18(1):22-25.
LIU Hesheng, TU Zhigang, XIONG Honghuai. Viscoelastic Constitutive Equation of Polymer Melts[J]. Polymer Materials Science& Engineering,2002,18(1):22-25.
[9]THIEN N P, TANNER R I. A New Constitutive Equation Derived from Network Theory[J]. Journal of Non-newton Fluid Mechanics,1977,2(4):353-365.
[10]FORTIN A, ZINE A. Computing Viscoelastic Fluid Flow Problems at Low Cost[J]. Journal of Non-newton Fluid Mechanics,1992,45(2):209-229.
[11]邓小珍. 塑料异型材气体辅助共挤出成型的实验和理论研究[D]. 南昌：南昌大学,2014.
DENG Xiaozhen. Experimental and Theoretical Study on Gas-assisted Co-extrusion of Plastic Profile with an Irregular Cross-section[D]. Nanchang: Nanchang University,2014.
[12]邓小珍, 柳和生, 黄益宾, 等. 气辅共挤出界面位置对挤出胀大的影响[J]. 高分子材料科学与工程,2013,29(9):114-118.
DENG Xiaozhen, LIU Hesheng, HUANG Yibin, et al. Influence of Interface Position on Die Swell in Gas-assisted Co-extrusion Molding Processes[J]. Polymer Materials Science& Engineering,2013,29(9):114-118.
[13]黄益宾, 柳和生, 黄兴元. 聚合物双组分复合共挤成型的挤出胀大研究[J]. 应用基础与工程科学学报,2010,18(4):657-665.
HUANG Yibin, LIU Hesheng, HUANG Xingyuan. Study on Extrudate Swell in Polymer Bicomponent Coextrusion Process[J]. Journal of Basic Science and Engineering,2010,18(4):657-665.

[1]	许谦1，2;胡广旭3;董志波4;任新星4;方洪渊4. 基于相变与收缩耦合的1Cr12焊缝冷却动态力学行为[J]. 中国机械工程, 2021, 32(03): 341-347.
[2]	刘志鹏;周杰;王时龙;王四宝;杨文翰. 基于有限元的多股螺旋弹簧疲劳寿命预测[J]. 中国机械工程, 2021, 32(02): 141-146.
[3]	蔡智媛1;王冰清1;彭旭东1，2;孟祥铠1，2 . 基于安装过程的O形圈安装结构优化分析[J]. 中国机械工程, 2019, 30(22): 2691-2697.
[4]	苏成阳;王志国. 基于网格曲面形状修改的柔性件装配偏差分析[J]. 中国机械工程, 2019, 30(19): 2294-2300.
[5]	陈泽芸;袁卫锋. 弹性力学中无网格和有限元耦合的元胞自动机算法[J]. 中国机械工程, 2017, 28(17): 2131-2135.
[6]	李杨, 吴运新, 龚海, 张宇, . 中子应力谱仪样品承重台回转支承载荷分析[J]. 中国机械工程, 2017, 28(12): 1434-1441.
[7]	董小闵, 毛飞, 魏燕. 基于压阻原理的磁流变减振器阻尼力传感器设计[J]. 中国机械工程, 2016, 27(20): 2699-2704.
[8]	欧文豪, 袁奇, 石清鑫. 基于整机瞬态热应力场重型燃气轮机转子的寿命评估[J]. 中国机械工程, 2015, 26(7): 929-935.
[9]	孙涛, 梁晋, 郭翔, 李磊刚, 任茂栋. 铜/铝复层板成形极限视觉测量方法及成形性能[J]. 中国机械工程, 2015, 26(7): 977-981.
[10]	王军, 马灿, 韩亚丽, 张淳. 离心力驱动液压膨胀式高速刀柄设计[J]. 中国机械工程, 2015, 26(21): 2941-2945,2962.
[11]	施红1;蒋彦龙1;刘娟1;蔡玉飞1;刘超2. 基于有限元的飞机空气高温高压导管应力设计[J]. 中国机械工程, 2014, 25(5): 614-618.
[12]	吴竹溪;李波;路冬;鲁宇明. 涂胶机器人移动机构装夹布局的递推优化算法[J]. 中国机械工程, 2014, 25(15): 2037-2043.
[13]	黄华贵1;王巍2;刘永1;杜凤山1. 大棒材芯部疏松缺陷控制与负张力轧制工艺研究[J]. 中国机械工程, 2014, 25(10): 1400-1405.
[14]	谈梅兰, 武国玉, 梁福祥. 基于ABAQUS的连杆疲劳分析[J]. 中国机械工程, 2013, 24(5): 634-638.
[15]	董永朋1, 2, 霍世慧1, 华林1, 王富生1, 岳珠峰1. 大展弦比复合材料机翼刚心分析与剪裁设计[J]. 中国机械工程, 2013, 24(1): 52-55.