基于凸集理论的绳牵引串并联机器人工作空间算法

摘要/Abstract

摘要： 为求解m≥n（m为绳索数目,n为机构自由度）绳牵引串并联机器人的力旋量可行工作空间,提出一种基于凸集理论的非迭代求解算法。该算法利用闵可夫斯基之和的性质构造绳索的旋量集,借助非迭代的数学思想验证该旋量集是否完全包含外部旋量集。首先,通过确定初始超平面找出凸集所有的边界超平面,根据初始超平面偏移的距离确定边界超平面投影位置; 然后推导出旋量平衡的判定表达式,并采用数值分析的方法得到绳牵引机器人的力旋量可行工作空间;最后,采用该算法对两种典型的绳牵引串并联机器人进行工作空间求解,结果验证了所提出的基于凸集理论工作空间求解方法的有效性。

关键词: 绳牵引机器人, 工作空间, 旋量理论, 凸集理论

Abstract: In order to solve the wrench feasible workspace of n-degrees-of-freedom serial and parallel manipulators driven by m cables, a non-iterative algorithm was proposed based on covex set theory. The properties of Minkowski Sum was introduced to construct the cable wrench set, and a non-iterative mathematical method was presented to verify if the wrench set fully included the external wrench set. Firstly, all boundary hyperplanes of convex set would be found by determining initial hyperplane. The projected boundary positions were determined according to the offset distance of the initial hyperplane. Then the explicit expression of the wrench equilibrium was deduced, and the wrench feasible workspace of cable-driven manipulator was obtained by using numerical analysis. The results demonstrate the effectiveness of the wrench feasible workspace analysis method based on convex set theory.

Key words: cable-driven manipulator, workspace, screw theory, covex set theory

中图分类号:

TP24

董晓东, 段清娟, 马彪, 段学超. 基于凸集理论的绳牵引串并联机器人工作空间算法[J]. 中国机械工程.

Dong Xiaodong, Duan Qingjuan, Ma Biao, Duan Xuechao. Workspace Algorithm of Cable-driven Serial and Parallel Manipulators Based on Convex Set Theory[J]. China Mechanical Engineering.

参考文献

[1]Lytle A M, Saidi K S, Bostelman R V, et al. Adapting a Teleoperated Device for Autonomous Control Using Three-dimensional Positioning Sensors: Experiences with the Nist RoboCrane[J]. Automation in Construction, 2004, 13(1):101-118.

[2]Kawamura S, Choe W, Tanaka S, et al. Development of an Ultrahigh Speed Robot Falcon Using Wire Drive System[C]//Proceedings of the Robotics and Automation. Nagoya: 1995 IEEE International Conference, 1995:215-220.

[3]訾斌,段宝岩,杜敬利.超大型天线馈源舱柔索支撑结构动力学分析与跟踪控制[J].控制理论与应用, 2007, 24(6):938-942.

Zi Bin, Duan Baoyan, Du Jingli. Dynamic Analysis and Tracking Control of the Cable-suspended System for the Five-hundred-meter Aperture Spherical Telescope[J]. Control Theory & Applications, 2007, 24(6):938-942.

[4]Gouttefarde M, Krut S, Pierrot F, et al. On the Design of Fully Constrained Parallel Cable-driven Robots [M].Springer: Advances in Robot Kinematics: Analysis and Design, 2008.

[5]Mustafa S K, Agrawal S K. On the Force-closure Analysis of N-dof Cable-driven Open Chains Based on Reciprocal Screw Theory[J]. IEEE Transactions on Robotics, 2012, 28(1):22-31.

[6]Duan Q, Vashista V, Agrawal S K. Effect on Wrench-feasible Workspace of Cable-driven Parallel Robots By Adding Springs[J]. Mechanism and Machine Theory, 2015, 86:201-210.

[7]Taghavi A, Behzadipour S, Khalilinasab N, et al. Workspace Improvement of Two-link Cable-driven Mechanisms with Spring Cable [M]. Springer: Cable-driven Parallel Robots， 2013.

[8]Ebert-Uphoff I, Voglewede P. On the Connections Between Cable-driven Robots, Parallel Manipulators and Grasping[C]//Proceedings of the Robotics and Automation. New Orleans：2004 IEEE International Conference, 2004:4521-4526.

[9]Bosscher P, Riechel A T, Ebert-Uphoff I. Wrench Feasible Workspace Generation for Cable-driven Robots[J]. IEEE Transactions on Robotics, 2006, 22(5):890-902.

[10]Bouchard S, Gosselin C, Moore B. On the Ability of a Cable-driven Robot to Generate a Prescribed Set of Wrenches[J]. Journal of Mechanisms and Robotics, 2010, 2(1):011010.

[11]于勇,罗思标,郭希娟,等.基于Minkowski的多面体快速碰撞检测算法[J].小型微型计算机系统, 2012, 33(11):2543-2547.

Yu Yong, Luo Sibiao, Guo Xijuan, et al. Collision Detection Minkowski Sum Polyhedra Ray Intersection Calculation[J]. Journal of Chinese Computer Systems, 2012, 33(11):2543-2547.

[12]Mao Y. Carex: a Cable-driven Arm M Exoskeleton for Functional Training of Arm Movement[D]. Ann Arbor: University of Delaware, 2012.

[13]Pham C B, Yeo S H, Yang G, et al. Force-closure Workspace Analysis of Cable-driven Parallel Mechanisms[J]. Mechanism and Machine Theory, 2006, 41(1):53-69.

[1]	尹猛, 徐志刚, 赵志亮, 韩伟, . 基于套索传动的五指灵巧手设计与主从控制[J]. 中国机械工程, 2021, 32(08): 951-959.
[2]	许允斗1,2;徐郑和1;杨帆1;赵云1;梅有恩1;周玉林1,2;姚建涛1,2;赵永生1,2. 考虑工作空间与力传递效率的新型五自由度混联机器人设计与分析[J]. 中国机械工程, 2019, 30(16): 1996-2002.
[3]	张彦斌1,2,3;荆献领1;韩建海1,2;陈子豪1. 新型RR-RURU踝关节康复机器人机构的设计与分析[J]. 中国机械工程, 2019, 30(14): 1734-1741.
[4]	沈惠平;吴成琦;许可;赵迎春;杨廷力. 一种零耦合度三平移并联机构的设计及运动学[J]. 中国机械工程, 2019, 30(06): 658-664.
[5]	沈惠平;赵迎春;许可;张震;杨廷力. 一种可重构、部分运动解耦的空间n维平移1维转动并联机构的拓扑及其运动学设计[J]. 中国机械工程, 2019, 30(04): 413-422.
[6]	韩雪艳1，2;王子义1，2;李仕华1，2;田志立1，2. 具有连续转轴的新型3-UPU并联机构的运动特性分析[J]. 中国机械工程, 2018, 29(20): 2460-2466.
[7]	沈惠平;许可;杨廷力. 运动解耦和低耦合度选择顺应性装配机器手臂并联机构的设计及其运动分析[J]. 中国机械工程, 2018, 29(08): 883-892.
[8]	王杰1;管声启1;夏齐霄2. 手指康复外骨骼机器人的结构优化设计[J]. 中国机械工程, 2018, 29(02): 224-229.
[9]	朱伟;顾开荣;王传伟;刘晓飞. 一种3T1R并联机构设计及运动学性能分析[J]. 中国机械工程, 2018, 29(01): 14-21.
[10]	裴九芳;许德章;王海. 基于旋量理论的三指机器人灵巧手逆运动学分析[J]. 中国机械工程, 2017, 28(24): 2975-2980.
[11]	艾青林;阮惠祥;陈教料;应申舜. 基于多维度空间耦合的六足机器人步态规划[J]. 中国机械工程, 2017, 28(23): 2829-2838.
[12]	周少瑞;刘宏昭. 一种3-CRCR/RPU对称并联机器人机构工作空间及运动学分析[J]. 中国机械工程, 2017, 28(20): 2500-2508.
[13]	朱明星1,2;高国琴1;吴军3;陈太平1. 一种并/混联汽车电泳涂装输送机构运动/力传递效率性能分析[J]. 中国机械工程, 2017, 28(18): 2152-2160.
[14]	曹瑞珉, 郝丽娜, 高金海. 一种大工作空间密度的压电微动二维工作台设计[J]. 中国机械工程, 2017, 28(09): 1016-1020,1028.
[15]	潘英, 方跃法, 汪丛哲. 五自由度3D打印并联机器人设计及分析[J]. 中国机械工程, 2016, 27(17): 2273-2279.