乘用车狭小面积追尾商用车的耐撞性优化

摘要/Abstract

摘要：

乘用车狭小面积重叠追尾碰撞对商用车后下部防护装置的耐撞性要求较高。针对乘用车狭小面积追尾商用车这一碰撞形式进行耐撞性分析，通过拓扑优化得到兼顾30%、50%、100%三种追尾重叠形式的商用车后下部防护装置最佳材料分布形式，并根据拓扑优化模型进行精细设计，提出了一种新型的针对狭小面积重叠碰撞的商用车后下部防护装置。将该防护装置运用于某型商用车上，并对其狭小面积追尾碰撞的耐撞性进行了仿真验证。

关键词: 商用车, 追尾碰撞, 后下部防护装置, 优化设计

Abstract:

Higher requirements are put forward toward RUG of commercial vehicles that is car to truck underride crashes in the narrow area overlap. Aiming at this phenomenon, considering 30%,50%,100% three kinds overlap crashes, through the topology optimization, the best material distribution form of RUG was obtained. According to results of topology optimization, a new kind of RUG was structured after elaborate design. Finally the new kind of RUG was applied to a certain type of commercial vehicle, and its crashworthiness of narrow area overlap crashes was validated.

Key words: commercial vehicle;underride crashes;rear , underride guards(RUG);optimization , design

中图分类号:

U467.14

邓善良, 姜, 潮, 邓青青. 乘用车狭小面积追尾商用车的耐撞性优化[J]. 中国机械工程, 2015, 26(21): 2970-2975.

Deng Shanliang, Jiang Chao, Deng Qingqing. Crashworthiness Optimization for Car to Truck Underride Crashes in Narrow Area Overlap[J]. China Mechanical Engineering, 2015, 26(21): 2970-2975.

参考文献

[1]潘婷,王宏雁.在我国推进载货汽车后下部防护装置法规的必要性[C]//2008中国汽车安全技术国际研讨会.上海:2008:407-411.
[2]Insurance Institute for Highway Safety.Underride Guards Can Fail in Real-world Crashes,and Crash Tests Demonstrate the Need for New Standards to Address the Deadly Problem,Status Report.Vol.46,No.2[R].Arlington:Insurance Institute for Highway Safety,2011.
[3]朱西产,程勇.载货汽车防护装置最佳离地高度和刚度的分析[J].汽车工程,2002,24(5):419-425.
Zhu Xichan,Cheng Yong.An Analysis on the Optimal Ground Clearance and Stiffness of Truck under-run Protector[J]. Automotive Engineering,2002,24(5):419-425.
[4]赵紫剑.商用车被动安全性仿真分析与改进设计[D].长春:吉林大学,2009.
[5]Krehl M,Riebeck L,Breitling U.Passive Safety of Trucks in Frontal and Rear-end Collisions with Cars[M].Detroit:Society of Automotive Engineers,2003.
[6]Mariolani J R L,de Arruda A C F,Schmutzler L O F.Development of New Underride Guards for Enhancement of Compatibility Between Trucks and Cars[C]//17th International Technical Conference on the Enhanced Safety of Vehicle.Amsterdam,2001,Paper Number 425:1-10.
[7]Cerniglia D,Lombardo E,Nigrelli V.Conceptual Design by TRIZ:an Application to a Rear Underrun Protective Device for Industrial Vehicle[C]//International Electronic Conference on Computer Science,AIP Conference Proceedings.Nanning:International Association of Engineers(IAENG)，2008:328-331.
[8]杨辉,董学勤,李佳琦,等.货车后下部防钻撞保护装置的研究[J].汽车工程,2009,31(12):1162-1164.
Yang Hui,Dong Xueqin,Li Jiaqi,et al.An Investigation into the Underrun Protection Device at the Bottom Rear-end of Truck[J]. Automotive Engineering,2009,31(12):1162-1164.
[9]Insurance Institute for Highway Safety.Rear Underride Guards Work Well But Most Could Do Better.Status Report.Vol.48,No.2[R].Arlington:Insurance Institute for Highway Safety,2013.
[10]周克民,李俊峰,李霞.结构拓扑优化研究方法综述[J].力学进展,2005,35(1):69-76.
Zhou Kemin,Li Junfeng,Li Xia.A Review on Topology Optimization of Structures[J].Advances in Mechanics,2005,35(1):69-76.
[11]Rietz A.Sufficiency of a Finite Exponent in SIMP(Power Law) Methods[J].Structural and Multidisciplinary Optimization,2001,21(2):159-163.
[12]张鹏飞,董瑞强.拓扑优化在白车身概念设计中的应用[J].汽车技术,2010(7):55-58.
Zhang Pengfei,Dong Ruiqiang.Application of Topology Optimization in BIW Concept Design[J].Automobile Technology,2010(7):55-58.
[13]陆善斌.商用车被动安全结构性设计研究[D].长春:吉林大学,2009.

[1]	鲁开讲, 师俊平, 张锋涛. 平面三自由度并联机构动力学优化设计 [J]. J4, 201016, 21(16): 1926-1931.
[2]	张琦1;李增亮1;董祥伟1;刘延鑫1;王雨婷2. 大功率潜水电机冷却系统分析方法与试验研究[J]. 中国机械工程, 2021, 32(03): 368-377.
[3]	张凯成；李舜酩；孙明杰. 钢铝材料结合的商用车车架多工况轻量化优化设计[J]. 中国机械工程, 2020, 31(18): 2206-2211，2219.
[4]	刘世豪, 林茂. [综述]高速数控转台优化设计方法研究现状与展望[J]. 中国机械工程, 2020, 31(13): 1629-1637.
[5]	高富东;王德心;王海东;曹建平. 基于射流冲击作用的舰机适配性数值分析与优化[J]. 中国机械工程, 2020, 31(12): 1425-1436.
[6]	吕凤鹏;李朝阳;黄健;陈兵奎. RV减速器转臂轴承的优化设计[J]. 中国机械工程, 2020, 31(09): 1043-1048.
[7]	邹伟生1;刘瑞仙1;刘少军2. 粗颗粒海底矿石浆体提升电泵研究[J]. 中国机械工程, 2019, 30(24): 2939-2944.
[8]	杨奇;甄文强;姬永强. 以减小初始扰动为目标的火箭弹定心部优化设计[J]. 中国机械工程, 2019, 30(21): 2611-2615.
[9]	陈东1;许敏2;李治3;郭松1;高彦凯1. 不等厚板激光拼焊在线碾压机构碾压轮结构参数优化设计[J]. 中国机械工程, 2019, 30(07): 872-876.
[10]	张旭1,2;张孟洁1;王格格1;李伟2,3;阮江涛1. 叶片表面粗糙条件下钝尾缘翼型优化设计[J]. 中国机械工程, 2019, 30(06): 728-734.
[11]	柯庆镝;李杰;吕岩;刘光复;宋守许. 基于结构和性能相似度分析函数的机械产品优化设计方法[J]. 中国机械工程, 2019, 30(05): 586-594.
[12]	朱佳栋;苏少辉;陈昌;刘桂英. 面向产品配置设计的改进交互式遗传算法[J]. 中国机械工程, 2018, 29(20): 2474-2478.
[13]	王倩蓉;姜潮;方腾. 一种考虑参数相关性的可靠性优化设计方法[J]. 中国机械工程, 2018, 29(19): 2312-2319,2326.
[14]	胡朝辉;崔雪姣;成艾国;秦晓凯. 基于均匀化循环理论的车身焊点布局优化方法[J]. 中国机械工程, 2018, 29(19): 2384-2388.
[15]	吴永伟;邬再新;鲍政伟. 卧式HMC500主轴系统热特性分析及结构优化[J]. 中国机械工程, 2018, 29(13): 1596-1602.