基于RCSA的深孔内圆磨床主轴端点频响函数预测

中国机械工程 ›› 2015, Vol. 26 ›› Issue (19): 2652-2661.

基于RCSA的深孔内圆磨床主轴端点频响函数预测

李孝茹;朱坚民;张统超;王健

上海理工大学，上海，200093

出版日期:2015-10-10 发布日期:2015-10-10
基金资助:
国家自然科学基金资助项目(50975179)；上海市教委科研创新项目(11ZZ136)；上海市科委科研计划资助项目(13160502500)；沪江基金资助项目(D14005)

Frequency Response Prediction of Deep Hole Internal Grinder Spindle Endpoint Based on Receptance Coupling Substructure Analysis

Li Xiaoru;Zhu Jianmin;Zhang Tongchao;Wang Jian

University of Shanghai for Science and Technology，Shanghai，200093

Online:2015-10-10 Published:2015-10-10
Supported by:
National Natural Science Foundation of China（No. 50975179）

摘要/Abstract

摘要：

基于响应耦合子结构分析法预测了深孔内圆磨床主轴端点的频响函数。首先对磨床主轴进行子结构划分，计算各子结构自由状态下的频响函数矩阵，然后顺序刚性耦合各子结构的频响函数矩阵，对轴承支撑点使用结构修改法修改轴承约束下的已耦合子结构频响函数矩阵，直至耦合到最后一个子结构，得到主轴端点的频响函数。以某深孔内圆磨床为研究对象，分别基于该方法和有限元法，对其主轴端点的频响函数进行预测，并对其进行实验测试。实验及分析结果表明：该方法预测精度高于有限元分析方法预测精度、计算速度快，便于深孔内圆磨床主轴系统的结构优化。

关键词: 深孔内圆磨床, 主轴端点, 频响函数预测, 响应耦合子结构分析, 结构修改法

Abstract:

Based on RCSA, this paper predicted the frequency response function of the endpoint of a deep hole internal grinder spindle. At first, the method separated the model of grinder spindle into several subsections to calculate their free-state frequency response function (FRF) matrices, then rigidly coupled the FRF matrices of each substructure sequentially, revised the FRF matrices of the coupled substructure with structural modification method at the support points of bearings, coupled till to the last substructure, then the FRF of the endpoint of grinder spindle was calculated．With a deep hole internal grinder spindle system as the research object, the paper predicted the FRF of the spindle endpoint through proposed method and finite element method, meanwhile a group of FRF data were collected by experiments．Experimental results indicate that this method, with higher prediction precision and faster calculation speed, is better in the structure optimization of the deep hole internal grinder spindle system.

Key words: deep hole internal grinder, spindle endpoint, frequency response characteristic prediction, receptance coupling substructure analysis(RCSA), structural modification method

中图分类号:

李孝茹, 朱坚民, 张统超, 王健. 基于RCSA的深孔内圆磨床主轴端点频响函数预测[J]. 中国机械工程, 2015, 26(19): 2652-2661.

Li Xiaoru, Zhu Jianmin, Zhang Tongchao, Wang Jian. Frequency Response Prediction of Deep Hole Internal Grinder Spindle Endpoint Based on Receptance Coupling Substructure Analysis[J]. China Mechanical Engineering, 2015, 26(19): 2652-2661.

参考文献

[1]胡如夫，孙庆鸿，陈南，等．高精度内圆磨床结构动态优化设计研究[J]．中国机械工程，2002，13(18)：1542-1544.
Hu Rufu，Sun Qinghong，Chen Nan，et al．Research on Structure Dynamic Optimization Design of High-precision of Internal Grinder[J]. China Mechanical Engineering，2002，13(18)：1542-1544.
[2]周晓玲，汪中厚，陈琪华，等．基于Pro/MECHANICA的深孔内圆磨床内圆磨具的精确建模及模态分析[J]. 制造业信息化，2006(1)：42-44.
Zhou Xiaoling，Wang Zhonghou，Chen Qihua，et al．Accurate Modeling and Modal Analysis of Deep Hole Grinding Tools Based on Pro/MECHANICA[J]．Journal of Manufacturing Automation,2006(1)：42-44.
[3]于天彪，王学智，关鹏，等．超高速磨削机床主轴系统模态分析[J]．机械工程学报，2012，48(17)：183-188.
Yu Tianbiao，Wang Xuezhi，Guan Peng，et al．Modal Analysis of Ultra-high-speed Grinding Spindle[J]．Journal of Mechanical Engineering，2012，48(17)：183-188.
[4]刘杰，李蓓智，杨建国，等．高速外圆磨床电主轴系统的有限元建模和动态性能分析[J]．东华大学学报，2012，38(5)：542-545.
Liu Jie，Li Beizhi，Yang Jianguo，et al．FEM Modeling and Dynamic Performance Analysis of Electric Spindle System of High Speed Cylinder Grinding Machine[J]．Journal of Donghua University，2012，38(5)：542-545.
[5]中国机械工程学会设备与维修工程分会．设备状态监测与故障诊断技术及其工程应用[M]．北京：机械工业出版社，2010．
[6]Filiz S，Cheng C H，Powell K B，et al．An Improved Tool Holder Model for RCSA Tool-point Frequency Response Prediction[J]．Precision Engineering，2009，33(1)：26-36.
[7]Movahhedy M R，Gerami J M．Prediction of Spindle Dynamics in Milling by Sub-structure Coupling[J]. International Journal of Machine Tools and Manufacture，2006，46(3/4)：243-251.
[8]Schmitz T L，Duncan G Scot．Three-component Receptance Coupling Substructure Analysis for Tool Point Dynamics Prediction[J]. Journal of Manufacturing Science and Engineering，2005，127(4)：781-790.
[9]柴银刚，孟德浩，龙新华，等．高速主轴[CD*2]夹具[CD*2]刀具系统动态特性分析[J]．噪声与振动控制，2013，33(6)：25-30．
Cai Yingang，Meng Dehao，Long Xinhua，et al．Analysis of Dynamic Characteristics of High Speed Spindle-holder-tool System[J]. Noise and Vibration Control，2013，33(6)：25-30.
[10]Wang Er-hua，Wu Bo，Hu You-min，et al．Dynamic Parameter Identification of Tool-spindle Interface Based on RCSA and Particle Swarm Optimization[J]．Shock and Vibration，2013，20(1)：69-78.
[11]Namazi M，Altintas Y，Abe T，et al．Modeling and Identification of Tool Holder-spindle Interface Dynamics[J]．International Journal of Machine Tools and Manufacture，2007，47(9)：1333-1341.
[12]Ertürk A，Budak E，zgüven H N．Analytical Modeling of Spindle-tool Dynamics on Machine Tools Using Timoshenko Beam Model and Receptance Coupling for the Prediction of Tool Point FRF[J]．International Journal of Machine Tools and Manufacture，2006，46(15)：1901-1912.
[13]Lee J，Schultz W W．Eigenvalue Analysis of Timoshenko Beams and Axisymmetric Mindlin Plates by the Pseudospectral Method[J]．Journal of Sound and Vibration，2004，269 (3/5)：609-621.
[14]Geist B，McLaughlin J R．Asymptotic Formulas for the Eigenvalues of the Timoshenko Beam[J]．Journal of Mathematical Analysis and Applications，2001，253(2)：341-380.
[15]Kivanc E B，Budak E．Structural Modeling of End Mills for Form Error and Stability Analysis[J]．International Journal of Machine Tools and Manufacture，2004，44(11)：1151-1161.
[16]Schmitz T L，Davies M A，Kennedy M D．Tool Point Frequency Response Prediction for High-speed Machining by RCSA[J]. Journal of Manufacturing Science and Engineering，2001，123 (4)：700-707.
[17]Aristizabal-Ochoa J D．Timoshenko Beam-column with Generalized End Conditions and Nonclassical Modes of Vibration of Shear Beams[J]. Journal of Engineering Mechanics，2004，130 (10)：1151-1159.
[18]zgüven H N．Structural Modifications Using Frequency Response Functions[J]．Mechanical Systems and Signal Processing，1990，4 (1)：53-63.