螺旋驱动杆式行波型超声电机

中国机械工程 ›› 2015, Vol. 26 ›› Issue (18): 2518-2524.

螺旋驱动杆式行波型超声电机

华顺明1,3;孟玉明1,2;李志强1,2;楼应侯1,3;李加林1,2

1.浙江大学宁波理工学院,宁波,315100
2.太原科技大学,太原,030024
3.浙江省零件轧制成形技术研究重点实验室,宁波,315100

出版日期:2015-09-25 发布日期:2015-09-23
基金资助:
国家自然科学基金资助项目（51275467);宁波市自然科学基金资助项目（2010A610129）

Rod Type Traveling Wave Ultrasonic Motor Based on Spiral-driving

Hua Shunming1,3;Meng Yuming1,2;Li Zhiqiang1,2;Lou Yinghou1,3;Li Jialin1,2

1.Institure of Technology,Zhejiang University,Ningbo,Zhejiang,315100
2.Taiyuan University of Science and Technology,Taiyuan,030024
3.Part Rolling Key Laboratory of Zhejiang Province,Ningbo,Zhejiang,315100

Online:2015-09-25 Published:2015-09-23
Supported by:
National Natural Science Foundation of China（No. 51275467）;Natural Science Foundation of Ningbo（No. 2010A610129）

摘要/Abstract

摘要：

设计了一种螺旋驱动杆式行波型超声电机，初步分析了其驱动机理。推导了螺纹牙型角与定子长度以及转子直径三者之间的关系，并以提高螺纹驱动效率为目标函数，确定了电机主要结构尺寸，优化了用于放大振幅的定子凹槽结构。加工制作了样机，并搭建了试验装置，测试了电机的主要性能参数。试验表明：电机实际工作频率为24.5kHz，与仿真结果基本一致；调节相差可实现正反转控制，启停灵敏；在220V驱动电压下，电机最大空载转速为40r/min,堵转轴向力为1.7N。

关键词: 精密螺旋传动, 压电驱动, 超声电机, 弯曲振型

Abstract:

A rod type traveling wave ultrasonic motor was designed based on spiral-driving and its working principles were preliminarily analyzed.The relationship among thread angle and stator length as well as rotor diameter was discussed. And then,setting efficiency improvement of screw transmission as object function, the main geometric parameters of stator could be determined.The size of groove was also optimized,which was used to amplify vibration amplitude.Based on these analyses,a prototype motor was fabricated. The corresponding experimental platform was established, and the main performances of motor were tested.The experimental results indicate that the actual working frequency is as 24.5kHz, which is in accordance with simulation one. The motor can be controlled to run clockwise or counter clockwise through alternating phase difference, and on-off operating characteristics are satisfied.Under driving voltage of 220V, the maximum rotary speed under no-load conditions is as 40r/min,and the locked axial force is as 1.7N.

Key words: precision , screw transmission;piezoelectric actuation;ultrasonic , motor;bending mode

中图分类号:

TM384

华顺明, 孟玉明, 李志强, 楼应侯, 李加林, . 螺旋驱动杆式行波型超声电机[J]. 中国机械工程, 2015, 26(18): 2518-2524.

Hua Shunming, Meng Yuming, Li Zhiqiang, Lou Yinghou, Li Jialin, . Rod Type Traveling Wave Ultrasonic Motor Based on Spiral-driving[J]. China Mechanical Engineering, 2015, 26(18): 2518-2524.

参考文献

[1]Uchino K, Cagatay S,Koc B.Piezoelectric Ultrasonic Motors [J]. Journal of Electroceramics,2004,13(1/3): 393-401.
[2]Ueha S,Tomikawa Y.Ultrasonic Motors:Theory and Application[M].Oxford:Clarendon Press,1993.
[3]周铁英,陈宇,鹿存跃,等.螺母型直线超声电机在透镜调焦中的应用[J].中国科学(E辑):技术科学,2009,39(10):1650-1654.
Zhou Tieying,Chen Yu,Lu Cunyue,et al.Application of Nut-type Linear Ultrasonic Motor in Focusing Lens[J].Science in China (Series E):Science and Technology,2009,39(10):1650-1654.
[4]Zhang J T,Huang W Q,Zhu H,et al.Lead Screw Linear Ultrasonic Motor Using Bending Vibration Modes[J].Transactions of Nanjing University of Aeronautics & Astronautics,2007,26(2):89-94.
[5]Henderson D. Ultrasonic Lead Screw Motor:US 6940209[P].2005-03-08.
[6]Henderson D A.Simple Ceramic Motor,Inspring Smaller Products[C]//10th International Conference on New Actuators. Bremen, 2006:1-4.
[7]程廷海,郭向东,包钢.中空柱状定子二阶弯振的旋转-直线超声电机[J].电机与控制学报,2013,17(3):8-12.
Cheng Tinghai,Guo Xiangdong,Bao Gang.Rotary-linear Ultrasonic Motor Based on Second Bending Vibration Mode of Hollow Cylindrical Stator[J].Electric Machines and Control,2013,17(3):8-12.
[8]屈维德,唐恒龄,张益群.北京:机械振动手册[M].2版.北京:机械工业出版社,2000.
[9]赵淳生.超声电机技术与应用[M].北京:科学出版社,2007.
[10]羊全钢,张凯,周铁英,等.弯曲旋转超声电机接触界面锥形角的分析与实验[J].声学学报,2002,27(5):413-419.
Yang Quangang,Zhang Kai,Zhou Tieying,et al.Analysis and Experiment on the Taper Angle of Contact Surface of Bend Rotation Ultrasonic Micromotors[J].Acta Acustica,2002,27(5):413-419.
[11]朱华,曾劲松,赵淳生.杆式超声电机定子的动力学分析与优化设计[J].中国机械工程,2008,19(21):2627-2632.
Zhu Hua,Zeng Jinsong,Zhao Chunsheng.Dynamics Analysis and Optimal Design of the Stator for a Rod-shape Ultrasomic Motor[J]. China Mechanical Engineering,2008,19(21):2627-2632.
[12]万志坚,胡泓.面内弯纵型直线超声电机的驱动与摩擦分析[J].振动.测试与诊断,2014,34(2):229-236.
Wan Zhijian,Hu Hong.Drive Mechanism and Friction Analysis of Linear Ultrasonic Motor Based on Longitudinal-bending Type[J]. Journal of Vibration,Measurement & Diagnosis,2014,34(2):229-236.
[13]李怀勇.新型杆式压电电机研究[D].秦皇岛，燕山大学，2013.

[1]	林超, 沈忠磊, 李坪洋, 郑山. 垂直型多级位移放大机构设计与力学解析建模[J]. 中国机械工程, 2021, 32(08): 908-915，937.
[2]	王建红1;周浩2;许有熊1;刘娣1. 基于膜式液压放大的压电驱动器设计与试验[J]. 中国机械工程, 2017, 28(21): 2567-2572.
[3]	胡俊峰, 郑昌虎, 蔡建阳. 一种微操作平台的自适应运动跟踪控制[J]. 中国机械工程, 2017, 28(08): 905-911,916.
[4]	王堃, 习俊通, . 压电膜片式微喷的多场耦合仿真模型及其应用[J]. 中国机械工程, 2017, 28(02): 233-240.
[5]	胡俊峰, 郑昌虎, 蔡建阳. 基于支持向量机的压电微操作平台非线性特性描述[J]. 中国机械工程, 2016, 27(22): 3012-3019.
[6]	李冲, 许立忠, 邢继春. 压电驱动器非线性机电耦合动力学求解与验证[J]. 中国机械工程, 2015, 26(24): 3275-3281.
[7]	孙士平, 胡政. 双足反向型直线超声电机的优化设计及性能仿真[J]. 中国机械工程, 2015, 26(13): 1783-1788.
[8]	周景亮1,2;陈超2;王均山2;郑伟1. 旋转型行波超声电机瞬态响应能力的试验研究[J]. 中国机械工程, 2014, 25(10): 1369-1373,1380.
[9]	董迎晖;唐茜;翟华;赵韩. 基于消除线性滑动的杆状超声电机研究[J]. 中国机械工程, 2013, 24(24): 3309-3313.
[10]	徐从裕, 孙雅琼, 方文琼, 罗洋, 袁航周. 超声电机微纳驱动参数调节机构设计[J]. 中国机械工程, 2013, 24(07): 886-889.
[11]	胡宁, 姚志远, 赵文涛. 直线超声电机柔性夹持元件的设计[J]. 中国机械工程, 2012, 23(9): 1089-1091,1098.
[12]	张健滔1, 朱华2, 赵淳生2. 杆式旋转超声电机在精密定位平台上的应用 [J]. 中国机械工程, 2011, 22(15): 1842-1846.
[13]	贺红林1, 2, 曾劲松3, 龙玉繁1, 刘文光1. 行波超声电机的运转特性及其电学建模研究 [J]. 中国机械工程, 2011, 22(14): 1639-1644.
[14]	陈如娟, 陈超, 宋小刚. 微小旋转型超声电机瞬态特性测试及机械特性估计方法 [J]. 中国机械工程, 2011, 22(11): 1284-1288.
[15]	尹育聪, 姚志远, 赵淳生. 行波型旋转超声电机两种组合方式的实验研究 [J]. 中国机械工程, 2011, 22(1): 84-87.