新型点磨削砂轮磨削参数对磨削温度影响研究

摘要/Abstract

摘要：

提出了一种带有粗磨区倾角θ的陶瓷结合剂CBN点磨削砂轮，这种新型砂轮具有磨除率高、加工精度好等优点。研究了磨削热产生与分配理论和红外测温原理。分别用不同θ角的砂轮在一系列磨削参数条件下磨削QT700材料的阶梯轴,用Thermovision A40M热像仪测量砂轮磨削工件时接触区的平均温度,得出了偏转角α、磨削深度ap、工件轴向进给速度vf和砂轮速度vs在磨削过程中对磨削温度的影响规律，并且比较了在同一组磨削参数下,三种不同θ角砂轮对磨削温度的影响情况。

关键词: 粗磨区倾角, 点磨削, 磨削参数, 磨削温度

Abstract:

A vitrified bond CBN point grinding wheel with coarse grinding area slope angle θ was presented.The removing rate of new grinding wheels is higher and the machining accuracy is better than that of conventional wheels. The theory of grinding heat generation and distribution and infrared temperature measurement were studied. These wheels with different coarse grinding area slope angle θ were used to grind the stepped shaft of QT700 with a series of grinding parameters. Thermovision A40M were used to measure the grinding contact area temperature. The effects of different grinding parameters such as deflection angle α, grinding depth ap, workpiece axial feed rate vf and wheel speed vs on grinding temperature were generalized.In the same group of grinding parameters, the effects of these different wheels on grinding temperature were contrasted.

Key words: coarse grinding area slope angle；point grinding；grinding parameter, grinding temperature

中图分类号:

TG580.6

尹国强, 巩亚东, 王超, 崔权 . 新型点磨削砂轮磨削参数对磨削温度影响研究[J]. 中国机械工程, 2015, 26(6): 716-720.

Yin Guoqiang, Gong Yadong, Wang Chao, Cui Quan. Study on Effects of Novel Point Grinding Wheels Processing Parameters on Grinding Temperature[J]. China Mechanical Engineering, 2015, 26(6): 716-720.

参考文献

[1]巩亚东,仇健,李晓飞,等.超高速点磨削相关机理研究[J].机械工程学报,2010,46(17):172-178.
Gong Yadong,Qiu Jian，Li Xiaofei,et al.Study on the Correlative Mechanism of Super High-speed Point Grinding[J].Journal of Mechanical Engineering,2010,46(17):172-178.
[2]徐鸿钧.磨削温度的测量技术[J].磨料磨具与磨削,1986,36(6):11-15.
Xu Hongjun.Grinding Temperature Measurement Technology[J].Diamond & Abrasives Engineering,1986,36(6):11-15.
[3]Malkin S.磨削技术理论与应用[M].蔡光起,巩亚东,宋贵亮,译.沈阳:东北大学出版社,2002.
[4]Quo C,Malkin S. Heat Transfer in Grinding[J].Journey of Materials Processing & Manufacturing Science,1992,1(1):16-27.
[5]Kuriyagawa T,Syoji K,Ohshita H.Grinding Temperature within Contact Arc between Wheel and Workpiece in High-efficiency Grinding of Ultrahard Cutting Tool Materials[J].Journal of Materials Processing Technology,2003,136(1):39-47.
[6]张国华.超高速磨削温度的研究[D].长沙:湖南大学,2006.
[7]Rowe W B, Morgan MN, Black S C E. A Simplified Approach to Control of Thermal Damage in Grinding[J]. Annals of the CIRP, 1996, 45(1):299-302.
[8]Chen Xun, Rowe W B. Analysis and Simulation of the Grinding Process—Part I：Generation of the Grinding Wheel Surface[J]. International Journal of Machine Tools and Manufacture,1996,36(8):871-882.
[9]Rowe W B, Black S C E, Mills B, et al. Experimental Investigation of Heat Transfer in Grinding[J]. CIRP Annals-Manufacturing Technology, 1995,44(1):329-332.
[10]孙丽,宦克为,邸旭,等.距离对红外热像仪测温精度的影响及校正方法研究[J].长春理工大学学报(自然科学版),2008,31(1):33-35.
Sun Li,Huan Kewei,Di Xu,et al.Research on the Influence Upon Accuracy of IR Thermal Temperature Measuring in Distance and Correction Method[J].Journal of Changchun University of Science and Technology(Natural Science Edition),2008,31(1):33-35.
[11]张先明.红外热像仪测温功能分析[J].激光与红外,2007,37(7):648-649.
Zhang Xianming. Study on the Measurement Temperature Function of Infrared Imaging System[J]. Laser & Infrared, 2007, 37(7): 648-649.
[12]Hwang J H, Kompella S, Chandrasekar S. Measurement of Temperature Field in Surface Grinding Using Infrared(IR) Imaging System[J]. ASME Transactions Journal of Tribology, 2003,125：377-383.

[1]	张高峰;龚俊明;李景焘;谢国广;孙昊. 形貌重构砂轮磨削试验研究[J]. 中国机械工程, 2020, 31(12): 1420-1424,1436.
[2]	彭锐涛1;吴艳萍1;唐新姿1;鲁鑫焱1;胡云波2. 流道出口位置对加压内冷却砂轮磨削性能的影响[J]. 中国机械工程, 2020, 31(04): 489-497.
[3]	张高峰;李景焘;王志刚;陈文新. 低温冷风纳米粒子微量润滑磨削轴承钢试验研究[J]. 中国机械工程, 2019, 30(19): 2342-2348.
[4]	彭锐涛1;李仲平1;黄晓芳1;唐新姿1;胡云波2. 加压内冷却方法在高温合金磨削中的应用[J]. 中国机械工程, 2017, 28(16): 2008-2015.
[5]	邓朝晖 , 刘涛, 廖礼鹏, 刘伟 , 万林林, 彭克立. 凸轮轴高速磨削温度的实验研究[J]. 中国机械工程, 2016, 27(20): 2717-2722.
[6]	霍文国, 丁元法, 张翔宇, 董庆运, 蔡兰蓉. 叶轮式内喷润滑剂砂轮的流场分析及实验研究[J]. 中国机械工程, 2016, 27(17): 2361-2366.
[7]	马廉洁, 陈杰, 巩亚东, 王佳. 基于PSO算法改进BP神经网络的氟金云母点磨削工艺参数优化[J]. 中国机械工程, 2016, 27(06): 761-766.
[8]	曾滔, 周志雄, 汤爱民, 肖思来, 左小陈. 碟形砂轮加工刀具螺旋槽的磨削参数研究[J]. 中国机械工程, 2015, 26(5): 575-580.
[9]	王艳, 谢建华, 刘建国, 张省. 基于瑞利分布的平面磨削温度场的仿真研究[J]. 中国机械工程, 2015, 26(4): 484-490.
[10]	马廉洁, 曹小兵, 巩亚东, 陈小辉. 基于遗传算法与BP神经网络的微晶玻璃点磨削工艺参数优化[J]. 中国机械工程, 2015, 26(1): 102-106.
[11]	田霖, 傅玉灿, 杨路, 赵家延. 钛合金Ti6Al4V高速磨削试验研究[J]. 中国机械工程, 2014, 25(22): 3056-3060.
[12]	丁兰英1，2;苏宏华1;徐鸿钧1;丁文锋1;范敏1. 有机粘结固体润滑剂涂层砂轮磨削性能研究[J]. 中国机械工程, 2013, 24(21): 2927-2932.
[13]	李秦峰, 任成祖, 张开飞. 磨削参数对ELID内圆磨削轴承外圈的影响[J]. 中国机械工程, 2013, 24(09): 1177-1180.
[14]	黄向明, 周志雄, 杨军, 汤爱民. 退火轴承钢磨削白层的形成机理研究 [J]. 中国机械工程, 2010, 21(24): 3018-3023.
[15]	仇健, 巩亚东, 刘月明, 修世超. 超高速点磨削砂轮的结构优化设计与制备 [J]. J4, 2009, 20(24): 2922-2927.