AZ31B镁合金板材旋压成形工艺研究

中国机械工程 ›› 2012, Vol. 23 ›› Issue (11): 1272-1275.

AZ31B镁合金板材旋压成形工艺研究

范有发;李东南;陈文哲

福建工程学院,福州,350108

出版日期:2012-06-10 发布日期:2012-06-14
基金资助:
福建省科技计划资助重点项目（2009H0001）；福建省新建本科院校新世纪优秀人才项目（GY-R0803）；福建工程学院人才培养模式创新实验区项目（E2500025）
Fujian Provincial Science and Technology Key Project ( No. 2009H0001)

Study on Spinning Process of AZ31B Magnesium Alloy Sheet

Fan Youfa;Li Dongnan;Chen Wenzhe

Fujian University of Technology, Fuzhou,350108

Online:2012-06-10 Published:2012-06-14
Supported by:

Fujian Provincial Science and Technology Key Project ( No. 2009H0001)

摘要/Abstract

摘要：

采用摩擦旋压成形工艺,研究了AZ31B挤压板材供应态试样在不预热的条件下直接进行旋压成形的可行性。结果表明,摩擦升温效应能迅速将坯料温度提高到200~450℃,从而提高镁合金板料的塑性变形能力,可旋压成形出最小直径为31.5mm、高度为9.22mm的镁合金碟形件。实验发现旋压成形的旋轮轴向进给量、旋轮运动轨迹、坯料旋转速度和润滑剂等对镁合金板材的旋压成形有较大的影响。当旋轮采用梳形运动轨迹、轴向进给量为0.22mm、坯料转速ω=900r/min时,采用MoS2钙基脂润滑,可获得较好的旋压成形效果。

关键词: AZ31B镁合金, 板材成形, 摩擦旋压工艺, 缺陷分析

Abstract:

The forming feasibility of AZ31B magnesium alloy sheet which was not preheated, was studied by friction spinning process. The results show that the plastic deformability of magnesium alloy sheet is increased, owing to the sheet metal temperature is increased from 200℃ to 450℃ with friction warming effect, and a dish component with 31.5mm diameter and 9.22mm height is produced successfully by spinning forming process. Furthermore, some parameters such as the axle feed rate and motion trail of screw wheel, rotation speed of feedstock and type of lubricant have a significant influence on the forming feasibility of magnesium alloy sheet. The spinning forming feasibility of AZ31B magnesium alloy sheet is good, when the motion trail of screw wheel is as comb, the axle feed of screw wheel is 0.22mm, the rotation speed of feedstock is 900r/min and MoS2 lubricant is adopted.

Key words: AZ31B magnesium alloy, sheet forming, friction spinning process, defect analysis

中图分类号:

TG306

范有发, 李东南, 陈文哲. AZ31B镁合金板材旋压成形工艺研究[J]. 中国机械工程, 2012, 23(11): 1272-1275.

FAN Wei-Fa, LI Dong-Na, CHEN Wen-Zhe. Study on Spinning Process of AZ31B Magnesium Alloy Sheet[J]. China Mechanical Engineering, 2012, 23(11): 1272-1275.

参考文献

[1]胡志清[1,2],李明哲[2].碟形件新型旋压成形工艺实验研究[J].锻压技术,2010(2):82-85.
[2]程秀全 [1],许业华 [2],夏琴香 [2].框架式三旋轮错距旋压成形装置的研制[J].锻压装备与制造技术,2005,40(6):31-35.
[3]陈云飞温彤侯模辉.V型劈开式皮带轮旋压成形过程的分析.金属铸锻焊技术,2009,.
[4]胡志清[1,2],李明哲[2],隋振[3],关文煜[4].基于连续多点成形原理的旋压成形技术[J].农业机械学报,2009(12):247-250.
[5]Quigley E, Monaghan J. Enhanced Finite Element Models of Metal Spinning[J]. Journal of Materials Processing Technology, 2002, 112(1):43-49.
[6]张艳秋[1],江树勇[1],孙金凤[2],赵立红[1].薄壁筒形件多道次滚珠旋压成形机理研究[J].锻压技术,2010,0(2):55-58.
[7]夏琴香[1],张赛军[1],梁佰祥[1],任晓龙[1],阮锋[1].三维非轴对称偏心类管件旋压成形时的变形力分析[J].机械工程学报,2005,41(10):200-204.
[8]马世成[1],王振杰[1],王东坡[1].带环向内加强筋异形件内旋压成形技术研究[J].锻压技术,2010(1):53-55.
[9]夏琴香[1],杨明辉[1],胡昱[1],程秀全[2].杯形薄壁矩形内齿旋压成形数值模拟与试验[J].机械工程学报,2006,42(12):192-196.
[10]李勇[1],许泽川[1],汤勇[1],曾志新[1].薄壁轴向微沟槽铜管高速旋压成形的数值模拟[J].华南理工大学学报：自然科学版,2010(1):128-133.
[11]毛柏平[1],汪发春[1],赵云豪[1],沈健[1].钛合金旋压性能的试验研究[J].稀有金属,2004,28(1):271-273.
[12]张佩武[1],夏伟[1],刘英[1],张卫文[1],陈维平[1].变形镁合金成形工艺研究及其应用[J].材料导报,2005,19(7):82-85.
[13]张文毓[1].镁合金及其加工技术研究进展[J].稀有金属快报,2007,26(8):15-19.
[14]王建军[1],王智民[1],白杉[2].日本镁合金的应用与研究现状[J].中国铸造装备与技术,2006(4):7-10.
[15]李德君[1],刘平[1],董企铭[1],田保红[1],任凤章[1].Mg-3Al-1Zn-0.8Nd合金热压缩变形流变应力的研究[J].材料热处理学报,2008,29(5):26-30.
[16]Takuda H, Morishita T, Kinoshita T, et al. Finite Element Simulation of Warm Deep Drawing of AZ31 Magnesium Alloy Sheet[J]. Journal of the Japan Society for Technology of Plasticity, 2006,47 (541) : 129-133.
[17]陈振华[1],程永奇[1],夏伟军[1],傅定发[1].AZ31镁合金薄板热拉深工艺研究[J].湖南大学学报：自然科学版,2005,32(1):83-86.
[18]张庭芳[1],黄菊花[1],杨国泰[1],邓敏[1],董懿琼[1],游步东[1].AZ31与ME20M镁合金板料热拉深性能实验研究[J].热加工工艺,2006,35(21):5-8.
[19]王鹏程[1],川井谦一[2],岳志勇[3].日本的镁合金旋压技术[J].锻压技术,2008,33(6):6-12.