应变强化奥氏体不锈钢力学行为研究及应用

中国机械工程 ›› 2011, Vol. 22 ›› Issue (21): 2633-2637.

应变强化奥氏体不锈钢力学行为研究及应用

韩豫1,2;陈学东1,2;刘全坤1;钱凌云1;陈从升1

1.合肥工业大学,合肥,230009

2.合肥通用机械研究院国家压力容器与管道安全工程技术研究中心,合肥,230031

出版日期:2011-11-10 发布日期:2011-11-16
基金资助:
国家高技术研究发展计划(863计划)资助重点项目(2009AA044802)；浙江省自然科学基金资助项目(Y111068)；安徽省教育厅自然科学基金资助项目(KJ2011B045)
National High-tech R&D Program of China (863 Program) （No. 2009AA044802）;

Zhejiang Provincial Natural Science Foundation of China（No. Y111068）;
Anhui Provincial Natural Science Foundation of Ministry of Education of China（No. KJ2011B045）

Study and Application on Mechanical Behavior of Austenitic Stainless Steels Based on Cold Stretching Technology

Han Yu1,2;Chen Xuedong1,2;Liu Quankun1;Qian Lingyun1;Chen Congsheng1

1.Hefei University of Technology,Hefei,230009

2.National Technology Research Center on Pressure Vessel and Pipeline Safety Engineering,

Hefei General Machinery Research Institute,Hefei,230031

Online:2011-11-10 Published:2011-11-16
Supported by:

National High-tech R&D Program of China (863 Program) （No. 2009AA044802）;

Zhejiang Provincial Natural Science Foundation of China（No. Y111068）;
Anhui Provincial Natural Science Foundation of Ministry of Education of China（No. KJ2011B045）

摘要/Abstract

摘要：

针对奥氏体不锈钢塑性和韧性优良但屈服强度低的问题,提出采用应变强化工艺来提高奥氏体不锈钢的屈服强度。研究了应变强化工艺中的两个关键工艺参数——应变量和应变速率对材料力学行为的影响。对应变量的研究结果表明,将奥氏体不锈钢的应变强化量控制在10%左右,材料的屈服强度可以得到显著提高。由此可大幅减薄压力容器的设计壁厚,实现压力容器的轻型化设计。与此同时,在10%左右的形变量下,因形变诱发的马氏体量很少,材料仍保持了较好的塑性和韧性,为压力容器的安全设计提供了保证。对应变速率的研究结果表明,在准静态条件下,奥氏体不锈钢材料力学性能指标对应变速率不敏感,但过小的应变速率会导致材料出现锯齿形屈服,产生Portevin-Le Chatelier(PLC)效应。

关键词:

应变强化, 奥氏体不锈钢, 屈服强度, 轻型化, 锯齿形屈服, Portevin-Le Chatelier(PLC)效应

Abstract:

Cold stretching technique was proposed in order to overcome the disadvantages of low yield strength for austenitic stainless steel(ASS). The key parameters for cold stretching were strain level and stain rate, and their influences on the material properties were investigated. Based on the control of different strain levels, the material parameters of strength, ductility and volume fraction of deformation-induced martensite were obtained. The results show that ASS's yield strength can be improved significantly by cold stretching technique and thus the wall thickness of pressure vessel can be substantially reduced. Meanwhile, ASS's ductility and toughness only to be minor affected, which will guarantee safe operation for pressure vessels. The test results also show that in the quasi-static conditions, the mechanical parameters of ASS are not sensitive to strain rate. However, too small strain rate will lead to occurrence of serrated yielding, which is called PLC effect.

Key words:

cold stretching, austenitic stainless steel(ASS), yield strength, lightweight, serrated yielding, Portevin-Le Chatelier(PLC) effect

中图分类号:

韩豫1, 2, 陈学东1, 2, 刘全坤1, 钱凌云1, 陈从升1.

应变强化奥氏体不锈钢力学行为研究及应用

[J]. 中国机械工程, 2011, 22(21): 2633-2637.

HAN Shu-1, 2, CHEN Hua-Dong-1, 2, LIU Quan-Kun-1, JIAN Ling-Yun-1, CHEN Cong-Sheng-1.

Study and Application on Mechanical Behavior of Austenitic Stainless Steels Based on Cold Stretching Technology

[J]. China Mechanical Engineering, 2011, 22(21): 2633-2637.

参考文献

[1]Marshall P. Austenitic Stainless Steels.. Microstructure and Mechanical Properties[M]. London: Elsevier Applied Science Pub. ,1984.
[2]韩豫[1],陈学东[2],刘全坤[1],孔韦海[1,2],汪志福[3].基于应变强化技术的奥氏体不锈钢压力容器轻型化设计探讨[J].压力容器,2010(9):16-20.
[3]郑津洋[1],郭阿宾[1],缪存坚[1],马利[1],吴琳琳[1].奥氏体不锈钢深冷容器室温应变强化技术[J].压力容器,2010(8):28-32.
[4]Johansson J I. Austenitic Stainless Steel Pressure Vessels:USA, 345683[P]. 1967-07-22.
[5]Ambrose S. Australian Practice with Cold Stretched Pressure Vessels[C]//9th International Conference on Pressure Vessel Technology. Sydney: ICPVT, 2000: 99-107.
[6]European Committee for Standardization. EN13458.- 2002 Cryogenic Vessels Static Vacuum Insulated Vessels[S]. Brussels: CEN, 2002.
[7]Swedish Standards Institute. Cold--stretching Di- rections 1991[S]. Stockholm:SIS, 1991.
[8]Standards Australia International. AS 1210 Supp2 --1999 Pressure Vessels--Cold Stretched Auste- nitie Stainless Steel Vessels[S]. Sydney: Standards Australia, 1999.
[9]ASME Boiler and Pressure Vessel Standards Com- mittee. Case 2596- Cold Stretching of Austenitic Stainless Steel Pressure Vessels [S]. New York: ASME, 2008.
[10]周宁[1],郑津洋[1],盛水平[2],韩树新[2],陈海云[2],刘延雷[2],缪存坚[1].铜制压力容器轻量化研究[J].压力容器,2010(11):8-12.
[11]郑津洋,董其伍,桑芝富主编.过程设备设计[M],2005:408.
[12]石德珂.材料科学基础[M],2003.
[13]徐祖耀.马氏体相变与马氏体[M].北京：科学出版社,1981.332.
[14]Talonen J, Nenonen P, Pape G. Effect of Strain Rate on the Strain -- induced γ→α'-martensite Transformation and Mechanical Properties of Aus- tenitic Stainless Steels[J]. Metallurgical and Materials Transactions A,2005,36(2) :421-431.
[15]江慧丰[1,2],陈学东[1],范志超[1],董杰[1,2],姜恒[1],陆守香[2].动态应变时效对316L不锈钢疲劳蠕变行为的影响[J].金属学报:326-330.
[16]江慧丰[1],张青川[1],徐毅豪[1],伍小平[1].固溶处理对Al-Cu合金中Portevin—Le Chatelier效应空域行为的影响[J].物理学报:409-412.
[17]Jiang H F,Zhang Q C,Sun L,et al. Effect of Sol- ute Concentration on the Serrated Flow in Solution -- treated A1-- 4% Cu Alloys[J]. Chinese Physics, 2006,15(5): 1051-1054.
[18]江慧丰.al合金中塑性失稳现象（portevin-le chatelier效应）的实验和机理研究 [D].中国科学技术大学,2006: