高强度钢内螺纹冷挤压振动信号的试验研究

中国机械工程 ›› 2011, Vol. 22 ›› Issue (14): 1656-1658,1663.

高强度钢内螺纹冷挤压振动信号的试验研究

缪宏1,2;左敦稳2;张瑞宏1;王树宏3

1.扬州大学,扬州,225000

2.南京航空航天大学,南京,210016

3.中国人民解放军驻五一一厂军事代表室,南京,210016

出版日期:2011-07-25 发布日期:2011-07-28
基金资助:
国家高技术研究发展计划(863计划)资助项目(SQ2008AA10XK1468859)
National High-tech R&D Program of China (863 Program) （No. SQ2008AA10XK1468859）

Experimental Study on Vibration Signals of High-strength-steel Internal Thread Formed by Cold Extrusion

Miao Hong1,2;Zuo Dunwen2;Zhang Ruihong1;Wang Shuhong3

1.Yangzhou University,Yangzhou,Jiangsu,225000

2.Nanjing University of Aeronautics and Astronautics,Nanjing,210016

3.Office of the Military Representatives from PLA to No. 511 Factory,Nanjing,210016

Online:2011-07-25 Published:2011-07-28
Supported by:
National High-tech R&D Program of China (863 Program) （No. SQ2008AA10XK1468859）

摘要/Abstract

摘要：

为减少内螺纹冷挤压过程中机床内外干扰力激励引起的受迫振动对螺纹加工质量和挤压丝锥寿命的影响，研究了不同挤压加工条件下高强度钢内螺纹冷挤压过程中的振动信号，并通过频谱分析分析了幅值与频率产生的原因。研究结果表明,不同挤压速度下振动幅值变化趋势相同，主振频率呈随机变化。不同冷却润滑方式下振动幅值与主振频率基本保持不变，当冷却润滑液的黏度超过32mm2/s时，振动幅值与频率会发生急剧变化,出现了高频振动,容易导致挤压丝锥的断裂。

关键词:

内螺纹, 冷挤压, 振动, 波形, 振动频率

Abstract:

In order to reduce the effects of the forced vibration caused by inside and outside disturbing forces of machine tool on the quality of thread and the life of extrusion tap, this paper researched the vibration signals in the cold extrusion process of high-strength-steel internal thread under different extrusion conditions, and the change reason was also analyzed through the spectrum analysis. The results show that the variation trend of the vibration amplitude values is similar under different extrusion velocities,

and the master oscillation frequency changes in a random way.The amplitude value of vibration and the master oscillation frequency remain virtually unchanged under different lubrication patterns. While the viscosity number of lubricant exceedes 32mm2/s,the amplitude value of vibration and the master oscillation frequency can change dramatically,and high frequency vibration appears,then causing rupture of the extrusion tap. 

Key words: internal thread, cold extrusion, vibration, wave shape, vibration frequency

中图分类号:

TG376.2

缪宏1, 2, 左敦稳2, 张瑞宏1, 王树宏3.

高强度钢内螺纹冷挤压振动信号的试验研究

[J]. 中国机械工程, 2011, 22(14): 1656-1658,1663.

JIU Hong-1, 2, ZUO Dui-Wen-2, ZHANG Rui-Hong-1, WANG Shu-Hong-3.

Experimental Study on Vibration Signals of High-strength-steel Internal Thread Formed by Cold Extrusion

[J]. China Mechanical Engineering, 2011, 22(14): 1656-1658,1663.

[1]	王国彪, 赖一楠, 范大鹏, 杨华勇, 王时龙. 新型精密传动机构设计与制造综述 [J]. J4, 201016, 21(16): 1891-1897.
[2]	王立存, 陈进, 张贤明, 陈国强. 基于泛函的制冷涡旋压缩机变壁厚涡旋型线理论及形状优化 [J]. J4, 201016, 21(16): 1898-1901.
[3]	李小力, 陈威, 闫蓉. 基于BP神经网络的空间轮廓误差自适应补偿 [J]. J4, 201016, 21(16): 1902-1906.
[4]	夏瑞雪, 卢荣胜, 刘宁, 董敬涛. 基于圆点阵列靶标的特征点坐标自动提取方法 [J]. J4, 201016, 21(16): 1906-1910.
[5]	陈立锋, 吴晓铃, 秦大同, 肖正明. 齿轮啮合过程摩擦功耗研究 [J]. J4, 201016, 21(16): 1911-1915.
[6]	李明磊, 贾育秦, 张学良, 刘丽琴, 杜娟, 温淑花, 兰国生. 基于多目标差异演化算法的并联机构结构优化 [J]. J4, 201016, 21(16): 1915-1920.
[7]	吴怀超, 吴白羽, 张秀华. 石蜡感温阀传热性能的数字仿真研究 [J]. J4, 201016, 21(16): 1921-1926.
[8]	鲁开讲, 师俊平, 张锋涛. 平面三自由度并联机构动力学优化设计 [J]. J4, 201016, 21(16): 1926-1931.
[9]	张敏杰, 王庆九, 管成. 并联式油液混合动力挖掘机动力系统仿真研究 [J]. J4, 201016, 21(16): 1932-1936.
[10]	刘安平, 刘济春. IPC-208B型原子力显微镜大范围扫描三维驱动系统研究 [J]. J4, 201016, 21(16): 1936-1940.
[11]	姚运萍, 王智渊. 螺栓连接受载能量损失与结合面参数识别 [J]. J4, 201016, 21(16): 1941-1943,1951.
[12]	陈建, 邓利娟. 恒力弹性机构的设计 [J]. J4, 201016, 21(16): 1944-1946.
[13]	罗洁思, 于德介, 史美丽. 基于SVD和线调频小波路径追踪的转速波动齿轮箱故障诊断 [J]. J4, 201016, 21(16): 1947-1951.
[14]	战晓磊, 辛洪兵, 汉斯·彼德　兰特斯. 基于虚拟现实的MOTOMAN-HP3型机器人运动学仿真 [J]. J4, 201016, 21(16): 1952-1954,1998.
[15]	苏厚军, 史铁林, 陈非. 高炉煤气透平机状态检修的设计与实施 [J]. J4, 201016, 21(16): 1955-1958.