内啮合齿轮泵内齿轮静压支撑研究

中国机械工程 ›› 2011, Vol. 22 ›› Issue (13): 1532-1537.

内啮合齿轮泵内齿轮静压支撑研究

张建卓;李康康

辽宁工程技术大学,阜新,123000

出版日期:2011-07-10 发布日期:2011-07-14
基金资助:
辽宁省科技厅工业攻关项目(2008220049)
Liaoning Provincial Key Technology R&D Program of Ministry of Science and Technology of China（No. 2008220049）

Study on Hydrostatic Support of Inner Gear in Inner Mesh Gear Pumps

Zhang Jianzhuo;Li Kangkang

Liaoning Technical University, Fuxin,Liaoning,123000

Online:2011-07-10 Published:2011-07-14
Supported by:
Liaoning Provincial Key Technology R&D Program of Ministry of Science and Technology of China（No. 2008220049）

摘要/Abstract

摘要：

在分析内啮合齿轮泵发生胶合失效的形成机理的基础上,详细分析了内齿轮在运行过程中的受力情况,推导出了作用于内齿轮内壁的液压与啮合力所产生的合力在x、y两方向上的分力公式,通过MATLAB计算在一个受力周期内的内齿轮内壁受力情况,得到作用于其内壁的合力摆动中心线角度和平均合力大小。以此为基础,计算得到在泵体内壁开设静压支撑槽的位置。最后进行样机试验,试验结果表明,在输出液压力达到20MPa且主轴转速为1500r/min时齿轮泵工作正常,无胶合发生。

关键词:

内啮合, 齿轮泵, 胶合, 静压支撑

Abstract:

The forming mechanism of inner mesh gear pumps' agglutination failure was studied herein.Then the force of inner gear during the process of operation was analyzed.The formula of the component force at the x,y direction which resulted from the hydraulic pressure and meshing force was deduced.The angle of swinging centerline and the average resultant force which was swinging between two angles in one cycle were obtained by MATLAB software.Based on the analysis results,the central position and the angle range of the hydrostatic support's channel were computed. The prototype experimental results show that there is no agglutination when the hydraulic pressure reaches 20MPa and the rotating speed of the main shaft reaches 1500r/min.

Key words: inner mesh;gear pump, agglutination, hydrostatic support

中图分类号:

TH137.51

张建卓, 李康康.

内啮合齿轮泵内齿轮静压支撑研究

[J]. 中国机械工程, 2011, 22(13): 1532-1537.

ZHANG Jian-Zhuo, LI Kang-Kang.

Study on Hydrostatic Support of Inner Gear in Inner Mesh Gear Pumps

[J]. China Mechanical Engineering, 2011, 22(13): 1532-1537.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/

http://www.cmemo.org.cn/CN/Y2011/V22/I13/1532

[1]	陈宗斌, 何琳, 廖健, . 直线共轭内啮合齿轮泵输出流量脉动的测试研究[J]. 中国机械工程, 2021, 32(15): 1801-1811.
[2]	刘小平1,2;郭斌1,2;崔德军1,2;吴振宇1,2;张立杰1,2. 基于二元维纳过程的小样本齿轮泵可靠寿命预测[J]. 中国机械工程, 2020, 31(11): 1315-1322.
[3]	孟繁忠, 董成国, 冯增铭, 程亚兵. 新型内啮合齿形链啮合迹线及多边形效应研究 [J]. 中国机械工程, 2011, 22(16): 1891-1895.
[4]	宋爱平;周骥平;吴伟伟;高尚;. 弧齿齿轮泵瞬间流量及其脉动特性研究[J]. J4, 2009, 20(19): 0-2392.