TC17钛合金在高温与高应变率下的动态压缩力学行为研究

中国机械工程

TC17钛合金在高温与高应变率下的动态压缩力学行为研究

牛秋林1,3;陈明2;明伟伟2

1.湖南科技大学机电工程学院，湘潭,411201
2.上海交通大学机械与动力工程学院,上海,200240
3.湖南科技大学难加工材料高效精密加工湖南省重点实验室，湘潭,411201

出版日期:2017-12-10 发布日期:2017-12-08
基金资助:
国家自然科学基金资助项目(51405294,51605161,51675204)
National Natural Science Foundation of China （No. 51405294,51605161,51675204）

Study on Dynamic Compressive Mechanics Behavior of TC17 Titanium Alloy at High Temperature and High Strain Rates

NIU Qiulin1,3;CHEN Ming2;MING Weiwei2#br#

1.College of Mechanical and Electrical Engineering, Hunan University of Science and Technology, Xiangtan，Hunan,411201
2.School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai,200240
3.Hunan Provincial Key Laboratory of High Efficiency and Precision Machining of Difficult-to-Cut Material, Hunan University of Science and Technology, Xiangtan,Hunan,411201

Online:2017-12-10 Published:2017-12-08
Supported by:
National Natural Science Foundation of China （No. 51405294,51605161,51675204）

摘要/Abstract

摘要： 采用微型分离式霍普金森压杆实验系统对TC17钛合金在高温、高应变率条件下的动态力学行为进行研究，测试材料的应力应变行为，分析实验温度、应变率和应变对其动态力学性能的影响规律。实验结果表明：当应变率为3000s-1时，TC17钛合金表现出明显的应变硬化效应，但在高温、高应变率条件下其应变硬化效应明显减弱;TC17钛合金具有应变率强化效应，但在温度升高过程中其应变率敏感性随着实验温度的升高而先减小后增大;实验温度对TC17钛合金的动态压缩力学行为的影响非常明显，温度敏感性因子随温度的升高大幅度增大。

关键词: 材料力学, 动态压缩力学行为, 分离式霍普金森压杆, TC17钛合金, 高应变率

Abstract: The dynamic mechanics behaviors of TC17 titanium alloy were studied under the conditions of high temperatures and high strain rates by using SHPB experimental system. The stress and strain behaviors of the materials were tested, and the effects of the experimental temperatures, strain rates and strains on the dynamic mechanics properties were analyzed. The experimental results show that when the strain rate is as 3000s-1, TC17 titanium alloy exhibits obvious strain hardening effects, but the strain hardening effects are weakened at high temperatures and high strain rates. TC17 titanium alloy has strain rate strengthening effect, but during the temperature increase processes, the strain rate sensitivity decreases firstly and then increases with the temperature increase. The effects of temperature on the dynamic compressive mechanics behaviors of TC17 titanium alloy are very obvious, and the temperature sensitivity factor increases with the temperature increase.

Key words: mechanics of materials, dynamic compressive mechanics behavior, split Hopkinson pressure bar(SHPB), TC17 titanium alloy, high strain rate

中图分类号:

TG146.2

牛秋林1,3;陈明2;明伟伟2. TC17钛合金在高温与高应变率下的动态压缩力学行为研究[J]. 中国机械工程.

NIU Qiulin1,3;CHEN Ming2;MING Weiwei2. Study on Dynamic Compressive Mechanics Behavior of TC17 Titanium Alloy at High Temperature and High Strain Rates[J]. China Mechanical Engineering.

参考文献

[1]JIAO Shenbo, GAO Chao, CHENG Li, et al. A Very High-cycle Fatigue Test and Fatigue Properties of TC17 Titanium Alloy[J]. Journal of Materials Engineering and Performance, 2016, 25(3):1085-1093.

[2]王宝林. 钛合金TC17力学性能及其切削加工特性研究[D]. 济南：山东大学，2013.
WANG Baolin. Study on The Mechanical Properties of Titanium Alloy TC17 and Characteristics in Machining[D]. Jinan: Shandong University, 2013.

[3]TAN Liang, ZHANG Dinghua, YAO Changfeng, et al. Evolution and Empirical Modeling of Compressive Residual Stress Profile after Milling, Polishing and Shot Peening for TC17 Alloy[J]. Journal of Manufacturing Processes, 2017, 26:155-165.

[4]NIU Qiulin, AN Qinglong, CHEN Ming, et al. Wear Mechanisms and Performance of Coated Inserts During Face Milling of TC11 and TC17 Alloys [J]. Machining Science and Technology, 2013, 17(3): 483-495.

[5]陈洋，裴传虎，李臻熙，等. α+β钛合金在高应变率下的动态力学性能[J].航空材料学报，2013，33（6）：8-12.
CHEN Yang, PEI Chuanhu, LI Zhenxi, et al. Dynamic Mechanical Behavior of α+β Titanium Alloys at High Strain Rate[J]. Journal of Aeronautical Materials, 2013，33(6)：8-12.

[6]WANG Baolin, AI Xing, LIU Zhanqiang, et al. Dynamic Behavior of Ti-17 Alloy under High Strain Rates at Elevated Temperatures[J]. Materials at High Temperatures, 2013, 30(2):145-150.

[7]LI Qiang, XU Yongbo, BASSIM M N. Dynamic Mechanical Properties in Relation to Adiabatic Shear Band Formation in Titanium Alloy-Ti17[J]. Materials Science and Engineering A, 2003, 358(1/2):128-133.

[8]WANG Kaixuan, ZENG Weidong, ZHAO Yongq-ing, et al. Hot Working of Ti-17 Ttitanium Alloy with Lamellar Starting Structure Using 3-D Processing Maps[J]. Journal of Materials Science, 2010, 45(21):5883-5891.
[9]于冰冰，陈志勇，赵子博，等. TC17钛合金电子束焊接接头的显微组织与力学性能研究[J]. 金属学报，2016，52(7):831-841.
YU Bingbing, CHEN Zhiyong, ZHAO Zibo, et al. Microstructure and Mechanical Properties of Electron Beam Weldment of Titanium Alloy TC17[J]. Acta Metallurgica Sinica, 2016, 52(7):831-841.

[10]黄伯云，李成功，石力开，等. 中国材料工程大典第4卷有色金属材料工程（上）[M]. 北京: 化学工业出版社，2006.
HUANG Boyun, LI Chenggong, SHI Likai, et al. China Materials Engineering Canon: Nonferrous Metal Materials Engineering (Part I)[M]. Beijing: Chemical Industry Press, 2006.

[11]ZHAN Hongyi, KENT D, WANG Gui, et al. The Dynamic Response of a β Ttitanium Alloy to High Strain Rates and Elevated Temperatures[J]. Materials Science and Engineering A,2014,607:417-426.

[12]张红，索涛，李玉龙. 不锈钢材料高温、高应变率下动态力学性能的试验研究[J].航空材料学报，2012，32(1)：78-83.
ZHANG Hong, SUO Tao, LI Yulong. Mechanical Behavior of a Stainless Steel Material at Elevated Temperatures and High Strain Rates[J]. Journal of Aeronautical Materials, 2012，32(1)：78-83.
[13]GUO Weiguo, TIAN Hongwei. Strain Rate Sensitivity and Constitutive Models of Several Typical Aluminum Alloys[J]. The Chinese Journal of Nonferrous Metals, 2009,19(1):56-61.