铜铝异种金属板压印连接与接头拉剪载荷研究

中国机械工程 ›› 2014, Vol. 25 ›› Issue (19): 2669-2673.

铜铝异种金属板压印连接与接头拉剪载荷研究

杨慧艳;何晓聪;邓成江;曾;凯;丁燕芳

昆明理工大学,昆明,650500

出版日期:2014-10-10 发布日期:2014-10-14
基金资助:
国家自然科学基金资助项目（50965009）

Study on Clinch Joining for Cu/Al Alloy Sheets and Mechanical Properties of Joints

Yang Huiyan;He Xiaocong;Deng Chengjiang;Zeng Kai;Ding Yanfang

Kunming University of Science and Technology,Kunming,650500

Online:2014-10-10 Published:2014-10-14
Supported by:
National Natural Science Foundation of China（No. 50965009）

摘要/Abstract

摘要：

采用一种新的塑性成形连接方法——压印连接方法来实现铜、铝合金板的连接,通过拉剪实验研究了连接接头的力学性能,并分析了铜、铝合金板的排列顺序对接头拉剪载荷的影响。实验结果表明,对于铜、铝复合接头,铜板在上时接头具有较高的拉剪载荷(3kN),是铝板在上时拉剪载荷的4.6倍。根据接头失效形式对复合接头进行优化后发现：下层铝板的厚度增大时,接头的拉剪强度略有增大,拉剪过程中的能量吸收明显增大;提高下板材料强度时,接头的拉剪载荷明显增大;铜板作为上板进行压印连接时,失效形式为颈部断裂失效,且接头的拉剪强度较大。

关键词: 压印连接, 复合接头, 组合顺序;力学性能

Abstract:

Clinch was adopted to join Cu and Al alloy sheets. Mechanical performance of the joints was studied based on the lap-shear tests, and the effects of sequence of sheets on the lap-shear load of clinched joint were analyzed at the same time. It can be seen from the experimental results that the clinched joints present higher lap-shear load when the upper sheet is Cu alloy rather than Al alloy. The lap-shear load is about 3kN, which is 4.6 times of the other one. The optimization for composite joints based on the joint failure modes was carried out. Results show that when the lower sheet thickness increases, the energy absorption increases obviously but the lap-shear load slightly. If the lower sheet is displaced by a sheet with higher material strength, lap-shear load of joints increases distinctly. A conclusion can be drawn from the joint failure modes that a high joint lap-shear load corresponds to the neck fracture mode.

Key words: clinch joining, composite joint, sequence of combination, mechanical property

中图分类号:

杨慧艳, 何晓聪, 邓成江, 曾, 凯, 丁燕芳. 铜铝异种金属板压印连接与接头拉剪载荷研究[J]. 中国机械工程, 2014, 25(19): 2669-2673.

Yang Huiyan, He Xiaocong, Deng Chengjiang, Zeng Kai, Ding Yanfang. Study on Clinch Joining for Cu/Al Alloy Sheets and Mechanical Properties of Joints[J]. China Mechanical Engineering, 2014, 25(19): 2669-2673.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/

http://www.cmemo.org.cn/CN/Y2014/V25/I19/2669

参考文献

[1]黄伯云．我国有色金属材料现状及发展战略[J].中国有色金属学报，2004,14（z1）：122-127．
Huang Boyun. Status and Developing Strategy for China’s Nonferrous Metal Materials Industry[J].The Chinese Journal of Nonferrous Metals，2004,14（z1）：122-127．
[2]夏春智，李亚江，王娟．Cu/Al异种金属连接的研究现状[J].焊接，2008(1):1-5.
Xia Chunzhi,Li Yajiang,Wang Juan.Research Status of Joining of Cu/Al Dissimilar Metals[J].Welding & Joining，2008(1): 1-5.
[3]龙伟民，张雷，程亚芳.铝与铜连接技术的研究[J].金属加工（热加工），2008（12）:47-50.
Long Weimin,Zhang Lei,Cheng Yafang. Research of Joining Technology of Cu/Al [J]. MW Metal Forming，2008(12):47-50.
[4]TOX Co..TOX板件冲压连接技术[J].现代零部件，2006(9):70-71.
TOX Co.. Press Joining Technology of TOX Plate[J].Modern Components，2006(9):70-71.
[5]Mori K, Abe Y, Kato T. Mechanism of Superiority of Fatigue Strength for Aluminium Alloy Sheets Joined by Mechanical Clinching and Self-pierce Riveting[J].Journal of Materials Processing Technology,2012, 212(9):1900-1905.
[6]He X. Recent Development in Finite Element Analysis of Clinched Joints[J].International Journal of Advanced Manufacturing Technology, 2010, 48(5/8):607-612.
[7]Mucha J. The Analysis of Lock Forming Mechanism in the Clinching Joint[J]. Materials and Design, 2011, 32(10):4943-4954.
[8]Lee C J, Kim J Y, Lee S K, et al.Design of Mechanical Clinching Tools for Joining of Aluminium Alloy Sheets[J]. Materials and Design, 2010, 31:1854-1861.
[9]Varis J P. The Suitability for Round Clinching Tools for High-strength Structural Steel[J]. Thin-Walled Structures, 2002, 40(3):225-238.
[10]Varis J P. The Suitability of Clinching as a Joining Method for High-strength Structural Steel[J]. Journal of Materials Processing Technology, 2003, 132(1/3):242-249.
[11]Carboni M, Beretta S, Monno M. Fatigue Behavior of Tensile-shear Loaded Clinched Joints[J]. Engineering Fracture Mechanics, 2006, 73(2): 178-190.
[12]Lee C J, Kim J Y, Lee S K, et al. Parametric Study on Mechanical Clinching Process for Joining Aluminum Alloy and High-strength Steel Sheets[J]. Journal of Materials Processing Technology, 2010, 24(1):123-126.
[13]Han L, Chrysanthou A, Young K W. Mechanical Behavior of Self-piercing Riveted Multi-layer Joints under Different Specimen Configurations[J].Materials and Design, 2007, 28(7):2024-2033.
[14]郑丽娟，向龙，刘会莹，等．异种钢焊接接头脉冲放电强化与力学性能分析[J].中国机械工程,2012,23（12）：1492-1495．
Zheng Lijuan,Xiang Long,Liu Huiying,et al.Pulse Current Discharge for Strengthening Welded Joints of Dissimilar Steel and Analysis of Mechanical Properties[J].China Mechanical Engineering，2012,23（12）：1492-1495.
[15]郑峰.铜与铜合金速查手册[M].北京：化学工业出版社，2008.