基于新型金刚石砂轮的Al2O3陶瓷磨削性能

中国机械工程 ›› 2014, Vol. 25 ›› Issue (16): 2240-2246.

基于新型金刚石砂轮的Al2O3陶瓷磨削性能

伍俏平1,2;邓朝晖1,2;赵前程1;潘占3;康辉民1,2;万林林1,2

1.湖南科技大学,湘潭,411201
2.难加工材料高效精密加工湖南省重点实验室,湘潭,411201
3.湖南大学国家高效磨削工程技术研究中心,长沙,410082

出版日期:2014-08-26 发布日期:2014-09-11
基金资助:
国家自然科学基金资助项目（51205126,50775069);湖南省自然科学基金青年人才联合培养项目(12JJB006)；湘潭市联合基金资助项目(11JJ9016)

Grinding Performance of a New Diamond Grinding Wheels in Machining Al2O3 Ceramic

Wu Qiaoping1,2;Deng Zhaohui1,2;Zhao Qiancheng1;Pan Zhan3;Kang Huimin1,2;Wan Linlin1,2

1.Hunan University of Science and Technology,Xiangtan,Hunan,411201
2.Hunan Provincial Key Laboratory of High Efficiency and Precision Machining of Difficult-to-Cut Material, Xiangtan, Hunan, 411201
3.National Engineering Research Center for High Efficiency Grinding,Hunan University,Changsha,Hunan,410082

Online:2014-08-26 Published:2014-09-11
Supported by:
National Natural Science Foundation of China（No. 51205126,50775069）

摘要/Abstract

摘要：

利用粉末注射成形和真空钎焊技术制备了一种新型金刚石砂轮，制备的新型金刚石砂轮具有金刚石把持力大、金刚石微刃有序排布等特点。进行了基于新型金刚石砂轮的Al2O3陶瓷磨削性能研究。实验结果表明：相对于普通树脂结合剂金刚石砂轮，新型金刚石砂轮磨削Al2O3陶瓷的加工表面形貌完整性较好,宏观裂纹和表面损伤相对较少;表面粗糙度较小,当进给速度为40mm/s、磨削深度为40μm时,加工表面粗糙度Ra在0.68μm左右;在相同实验条件下,新型金刚石砂轮的磨削力减小了12%~17%,磨削温度降低了80~120℃。

关键词: 新型金刚石砂轮, 树脂结合剂砂轮, 氧化铝陶瓷, 磨削性能

Abstract:

A new diamond grinding wheel was prepared by powder injection molding and vacuum brazing, the new diamond wheel had a larger number of cutting edges which were artificially ordered so as to have big chip storage space, and it realized strong adhesion between diamonds and brazing alloy due to vacuum brazing. The paper discussed the grinding performance of the new diamond wheel in machining Al2O3 ceramic. The experimental results indicate that the quality of the machined work-piece surface is better than that machined by the conventional resin bond diamond wheel, the surface roughness is as 0.68μm when the feed speed is as 40mm/s and the depth of grinding is as 40μm, and the forces decreases by 12%~17% in compassion with conventional resin bond diamond wheel, and grinding temperature is reduced 80~120℃.

Key words: new diamond grinding wheel, resin bond diamond wheel, Al2O3 ceramic, grinding performance

中图分类号:

TG743

伍俏平, 邓朝晖, 赵前程, 潘占, 康辉民, 万林林, . 基于新型金刚石砂轮的Al2O3陶瓷磨削性能[J]. 中国机械工程, 2014, 25(16): 2240-2246.

Wu Qiaoping, Deng Zhaohui, Zhao Qiancheng, Pan Zhan, Kang Huimin, Wan Linl. Grinding Performance of a New Diamond Grinding Wheels in Machining Al2O3 Ceramic[J]. China Mechanical Engineering, 2014, 25(16): 2240-2246.

参考文献

[1]邓朝晖,伍俏平,张高峰,等.新型砂轮研究进展及其展望[J].中国机械工程,2010,21(21):2632-2637.
Deng Zhaohui,Wu Qiaoping,Zhang Gaofeng,et al.Recent Advances and Future Perspectives in New Type Grinding Wheel[J]. China Mechanical Engineering,2010,21(21):2632-2637.
[2]Chattopadhyay A K,Chollet L,Hintermann H E. On Performance of Brazed Boned Monolayer Diamond Grinding Wheel[J]. Annals of the CIRP,1991,40(1)：347-350．
[3]伍俏平,邓朝晖,潘占,等.钎焊气氛对金刚石钎焊性能的影响[J].机械工程学报,2012,48(4):51-57.
Wu Qiaoping,Deng Zhaohui,Pan Zhan,et al.Effect of Brazing Atmosphere on Brazing Performance of Diamond[J].Chinese Journal of Mechanical Engineering,2012,48(4):51-57.
[4]Chattopadhyay A K,Chollet L,Hintermann H E.Experimental Investigation on Induction Brazing of Diamond with Ni-Cr Hardfacing Alloy under Argon Atmosphere[J].Journal of Materials Science,1991,26:5093-5100.
[5]Nguyen T,Zhang L C.Modelling of the Mist Formation in a Segmented Grinding Wheel System[J].International Journal of Machine Tools and Manufacture,2005,45(11):21-28.
[6]Nguyen T,Zhang L C.The Coolant Penetration in Grinding with a Segmented Wheel-Part 1:Mechanism and Comparison with Conventional Wheels[J].International Journal of Machine Tools and Manufacture,2005,45(11):1412-1420.
[7]Tanaka T.New Development of Metal Bonded Diamond Wheel with Pore by the Growth of Bonding Bridge[J].Japan Soc. Precision Engineering,1992,26(1):27-32.
[8]Truong S H,Isono Y,Tanaka T.Scanning Electron Microscopic Study and Mechanical Property Examination of a Bond Bridge:Development of a Porous Metal Bonded Diamond Wheel[J].Journal of Materials Processing Technology, 1999, 89: 385-391.
[9]Tomino H,Kondo Y,Tojyo T.Pulse Electric Current Sintering Behavior of Atomized Cast-iron Diamond Composite Powder[J]. Journal of the Society of Materials Science,1999,48(6):585-591.
[10]Yamaguchi K,Horaguchi I,Sato Y.Grinding with Directionally Aligned SiC Whisker Wheel-loading Free Grinding[J]. Precision Engineering,1998,22(2):59-65.
[11]Yamaguchi K,Kikuzawa K,Wei Y Q,et al.Grinding Characteristics of Directionally Aligned SiC Whisker Wheel(Comparison with Al2O3 Fiber Wheel)[J].Transactions of the Japan Society of Mechanical Engineers(Series C)(in Japanese),1999,638(65):342-347.
[12]Smith N P,Smith D J,Pearce T R,et al.The Ductile Grinding of Glass Using Diamond Fibers Oriented Radially in a Grinding Wheel[J].Journal of Engineering Manufacture,2003,217:387-396.
[13]May P W,Rego C A,Thomas R M,et al.Preparation of Solid and Hollow Diamond Fibers and the Potential for Diamond Fiber Metal Matrix Composites[J].Journal of Materials Science Letter,1994,13:247-249.
[14]Aurich J C,Braun O,Warnecke G,et al.Development of Super-abrasive Grinding Wheel with Defined Grain Structure Using Kinematic Simulation[J].Annals of the CIRP,2003,52(1):275-280.
[15]Aurich J C,Herzenstile P,Sudermann H,et al.High Performance Dry Grinding Using a Grinding Wheel with a Defined Grain Pattern[J].Annals of the CIRP,2008,57(1):357-362.
[16]Pinto F W,Vargas G E,Wegener K.Simulation for Optimizing Grain Pattern on Engineered Grinding Tool[J].Annals of the CIRP,2008,57:353-356.
[17]Wu Qiaoping,Deng Zhaohui,Gong Yanli.Research on Grinding Temperature of a New Diamond Grinding Wheel[J]. Advanced Materials Research,2013,652-654:2205-2208.
[18]伍俏平,邓朝晖,潘占,等.金刚石纤维砂轮的制备及磨削表面质量研究[J].机械工程学报,2014,50(11):205-212.
Wu Qiaoping,Deng Zhaohui,Pan Zhan,et al.Preparation and Grinding Surface-Quality of a New Diamond Fiber Wheel[J]. Chinese Journal of Mechanical Engineering,2014,50(11):205-212.
[19]邓朝晖,伍俏平,张高峰,等.纤维状聚晶金刚石复合片刀具的切削性能及刀具磨损机理[J].机械工程学报,2011,47(7):178-184.
Deng Zhaohui,Wu Qiaoping,Zhang Gaofeng,et al.The Cutting Performance and Wear Mechanisms of A New Polycrystalline Diamond Compacts Cutter Tool[J].Chinese Journal of Mechanical Engineering,2011,47(7):178-184.