材料性能对搅拌摩擦焊焊缝成形的影响

中国机械工程 ›› 2014, Vol. 25 ›› Issue (15): 2102-2106.

材料性能对搅拌摩擦焊焊缝成形的影响

鲁煌;邢丽;杨成刚;黄春平;柯黎明

南昌航空大学，南昌，330063

出版日期:2014-08-10 发布日期:2014-08-13
基金资助:
国家自然科学基金资助项目（50875119，51265043，51165038）；江西省高等学校科技落地计划资助项目(KJLD12074)；航空科学基金资助项目（20111156004，2011ZE56005）

Influences of Material Properties on Welding Formation in Friction Stir Welding

Lu Huang;Xing Li;Yang Chenggang;Huang Chunping;Ke Liming

Nanchang Hangkong University,Nanchang,330063

Online:2014-08-10 Published:2014-08-13
Supported by:
National Natural Science Foundation of China（No. 50875119，51265043，51165038）;Aviation Science Foundation of China（No. 20111156004，2011ZE56005）

摘要/Abstract

摘要：

采用左螺纹圆柱搅拌头对O态和T4态2024铝合金进行搅拌摩擦焊接试验，研究了材料性能对搅拌摩擦焊焊缝成形的影响，并用软性约束分析了材料性能对焊核尺寸的影响。试验结果表明：焊缝形貌受焊核周边金属约束的影响，约束程度与材料力学性能和温度有关。O态2024铝合金对接焊时，软性约束体对塑性金属横向迁移的约束小，焊核面积和焊核宽度较T4态2024铝合金的焊核面积和焊核宽度大。两种热处理状态2024铝合金对接焊时，强度和硬度较高的T4态2024铝合金置于返回边时，在焊缝两侧、前进边的软性约束体对塑性金属的约束较返回边的软性约束体对塑性金属的约束强，焊核向返回边偏移;由于在返回边有更多的塑性金属，使其沿焊缝厚度方向向上的运动趋势增强，因此返回边的焊核高度较前进边的焊核高度高。对T4态2024铝合金进行适当的预热，会增强焊缝金属的塑化程度，使其向焊缝两侧的迁移运动趋势增强，焊核宽度及面积增大。

关键词: 软性约束, 搅拌摩擦焊, 材料性能, 塑性流动, 焊核

Abstract:

The 2024-O and 2024-T4 aluminum alloy were welded by friction stir welding with column lefthand-thread pins, and the influences of the material properties on the friction stir weld formation was investigated. Soft constraints were applied to explain the impact of the material properties on the size of nugget. The results show that the weld morphology is constrained by the surroundings of nugget, and the constraints are related to material properties and weld temperature. Under the same heat-treated state material, the area and width of the nugget of 2024-O aluminum alloy are greater than that of 2024-T4 aluminum alloy, due to the smaller constraint of lateral migration of plastic metal by the soft constraint body. While 2024-O aluminum alloy and 2024-T4 aluminum were welded with butt welding, taking the higher strength of 2024-T4 aluminum alloy as the retreated side, the constraint of the advanced side are stronger than the constraint of retreated side by both sides of the welding' soft constraint body, and the welding nugget is moved to the retreated side; the direction up of movement trend of the welding nugget which is made along the weld thickness is enhanced owing to the more plastic metal of retreated side, the welding nugget height of retreated side is higher than that of advanced side. Under the appropriate preheating conditions of 2024-T4 aluminum alloy, due to the increasing of plasticized metal in the weld and transverse migration of plastic metal，the width and area of the nugget are increased.

Key words: soft constraint, friction stir weld, material property, plastic flow, nugget

中图分类号:

TG456.9

鲁煌, 邢丽, 杨成刚, 黄春平, 柯黎明. 材料性能对搅拌摩擦焊焊缝成形的影响[J]. 中国机械工程, 2014, 25(15): 2102-2106.

Lu Huang, Xing Li, Yang Chenggang, Huang Chunping, Ke Liming. Influences of Material Properties on Welding Formation in Friction Stir Welding[J]. China Mechanical Engineering, 2014, 25(15): 2102-2106.

参考文献

[1]Reynolds A P. Flow Visualization and Simulation in FSW[J]. Scripta Materialia, 2008, 58(5): 338-342.
[2]Khorrami M S, Kazeminezhad M, Kokabi A H. Mechanical Properties of Severely Plastic Deformed Aluminum Sheets Joined by Friction Stir Welding[J]. Materials Science and Engineering A, 2012, 543: 243-248.
[3]Seidel T U, Reynolds A P. Visualization of the Material Flow in AA2195 Friction-stir Welds Using a Marker Insert Technique[J]. Metallurgical and Materials Transaction A, 2001, 32(11): 2879-2884.
[4]Buffa G, Donati L, Fratini L, et al. Solid State Bonding Mechanics in Extrusion and FSW: Experimental Tests and Numerical Analyses[J]. AIP Conference Proceedings, 2007, 907(1): 590-595.
[5]McQueen H J, Cabibbo M, Evangelista E. Piercing/Extrusion and FSW Nugget Microstructure Formation in Al Alloys[J]. Materials Science and Technology, 2007, 23(7): 803-809.
[6]Arbegast W J. Modeling Friction Stir Joining as a Metal Working Process[C]//TMS Annual Meeting: Hot Deformation of Aluminum Alloys. San Diego, California, 2003: 313-327．
[7]ASM International Handbook Committee. ASM Handbook Vol 2: Nonferrous Alloys and Special-purpose Materials[M]. Materials Park, OH, USA: ASM International，1996.
[8]柯黎明, 潘际銮, 邢丽, 等. 搅拌针形状对搅拌摩擦焊焊缝截面形貌的影响[J]. 焊接学报, 2007, 28(5): 33-37.
Ke Liming, Pan Jiluan, Xing Li, et al. Influence of Pin Shape on Weld Transverse Morphology in Friction Stir Welding[J]. Transactions of the China Welding Institution, 2007, 28(5): 33-37.
[9]Chen Z W, Pasang T, Qi Y. Shear Flow and Formation of Nugget Zone during Friction Stir Welding of Aluminum Alloy 5083-O[J]. Materials Science and Engineering A, 2008, 474(1/2): 312-316.
[10]王希靖, 李晶, 达朝炳, 等. LY12搅拌摩擦焊接过程中搅拌针摩擦行为的研究[J]. 热加工工艺, 2006, 35(3): 18-21.
Wang Xijing, Li Jing, Da Chaobing, et al. Analysis of Friction Action in LY12 Friction Stir Welding[J]. Hot Working Technology, 2006, 35(3): 18-21.

[1]	方远方, 张华. 铝合金型材的静轴肩倾斜搅拌摩擦焊接头性能[J]. 中国机械工程, 2021, 32(07): 815-820.
[2]	贺地求1;王东曜2;胡雷2;王海军2. 2198-T3S铝锂合金组合工艺搅拌摩擦焊接头组织性能分析[J]. 中国机械工程, 2020, 31(05): 610-615.
[3]	汤一博1;孙宏波2;余海东1;郑斌1;来新民1. 夹具拘束下大型薄壁铝合金结构搅拌摩擦焊接变形特性[J]. 中国机械工程, 2019, 30(15): 1881-1889.
[4]	张玉存1;崔妍1;付献斌2;孙世烜3. 搅拌摩擦焊核心区温度在线检测方法[J]. 中国机械工程, 2019, 30(14): 1658-1664,1672.
[5]	李小霞1，2;黄亮1，2;李建军1，2;王泽宇1，2. 搅拌摩擦焊和热处理复合工艺对2219铝合金组织性能的影响[J]. 中国机械工程, 2017, 28(23): 2880-2888.
[6]	姬书得, 温泉, 吕赞, 杨占鹏. 激冷影响TC4钛合金FSW残余应力与变形的规律[J]. 中国机械工程, 2016, 27(04): 531-536,543.
[7]	王家兴, 倪雁冰, 董娜, 吴楠. 搅拌摩擦焊接装备工作载荷预估及刚度分析[J]. 中国机械工程, 2016, 27(02): 258-264.
[8]	宋晓抗;赵军. 管件压力矫直过程中材料性能参数在线识别[J]. 中国机械工程, 2014, 25(10): 1357-1361.
[9]	张金峰1;巩亚东2;张永震2;刘月明2. 高速微尺度铣削分力的试验研究[J]. 中国机械工程, 2013, 24(23): 3225-3230.
[10]	李海利, 邢丽, 吴鸿燕. 焊接参数对搅拌摩擦焊焊缝形貌的影响 [J]. 中国机械工程, 2011, 22(14): 1737-1741.
[11]	张昭;别俊;. 搅拌摩擦焊接过程数值仿真的完全热力耦合模型[J]. J4, 2008, 19(10): 0-1257.