宽温度域工况下汽车水泵O形密封圈的密封性研究

中国机械工程 ›› 2014, Vol. 25 ›› Issue (15): 2013-2016,2023.

宽温度域工况下汽车水泵O形密封圈的密封性研究

解芳1,2;冯长虹3;王召兴3;陈铁军1

1.郑州大学，郑州，450001
2.南阳理工学院，南阳，473004
3.河南省西峡汽车水泵股份有限公司，西峡，474500

出版日期:2014-08-10 发布日期:2014-08-13
基金资助:
中国博士后科学基金资助项目（2013M541985）；2012年度河南省博士后科研基金资助项目（2012091）；河南省教育厅科学技术研究重点项目（13A460808）

Study on Sealing Property of O-ring Seal of Automobile Water Pump under Broad Temperature Region

Xie Fang1,2;Feng Changhong3;Wang Zhaoxing3;Chen Tiejun1

1.Zhengzhou University,Zhengzhou,450001
2.Nanyang Institute of Technology,Nanyang,Henan,473004
3.Henan Province Xixia Automobile Water Pump Limited Company,Xixia,Henan,474500

Online:2014-08-10 Published:2014-08-13
Supported by:
Supported by China Postdoctoral Science Foundation（No. 2013M541985）;Henan Provincial Science and Technology Program of Ministry of Education of China（No. 13A460808）

摘要/Abstract

摘要：

针对汽车发动机水泵O形橡胶密封圈宽温度域的工况特点，构建其与温度相关的Mooney-Rivlin材料模型，探讨冷却液温度、压力、摩擦因数等对O形密封圈接触压力、等效应力以及密封性的影响。研究表明：温度的升高将引起接触压力及等效应力的峰值呈幂指数减小，导致密封可靠性降低，但在宽温度域（-40~130℃）工况下，接触压力的峰值始终远大于液体压力，因此该密封圈具有可靠的密封性;液体压力的增大虽然会引起接触压力峰值增大，但其增大的速度比液体压力增大的速度小，因此将引起密封可靠性下降;摩擦因数对密封可靠性的影响不大。

关键词: 密封圈, 温度, 接触压力, 等效应力, 密封性

Abstract:

Based on the characteristics of rubber O-ring of an automobile engine water pump working in wide temperature domain, a Mooney-Rivlin material model which was relevant to temperature was established to reveal the influences of temperature, fluid pressure and friction coefficient on the contact pressure, equivalent stress and sealing property. The results show that the increase of temperature causes the peak of contact pressure and equivalent stress to decrease exponentially, inducing the sealing reliability reduces. However, the peak of contact pressure of O-ring working in -40~130℃ is considerably larger than that of the fluid pressure, so the O-ring has reliable sealing property. Furthermore, although the increase of fluid pressure induces the increase of the peak of contact pressure, the reliability of sealing will decline for that the increasing speed of contact pressure is lower than that of fluid pressure. Additionally, the friction coefficient has little influence on the reliability of sealing.

Key words: seal, temperature, contact pressure, equivalent stress, sealing property

中图分类号:

TH122

解芳, 冯长虹, 王召兴, 陈铁军. 宽温度域工况下汽车水泵O形密封圈的密封性研究[J]. 中国机械工程, 2014, 25(15): 2013-2016,2023.

Xie Fang, Feng Changhong, Wang Zhaoxing, Chen Tiejun. Study on Sealing Property of O-ring Seal of Automobile Water Pump under Broad Temperature Region[J]. China Mechanical Engineering, 2014, 25(15): 2013-2016,2023.

参考文献

[1]解芳，冯长虹，王召兴，等. 汽车发动机水泵带轮结构改进设计[J]. 机械强度, 2014, 36(2): 285-289.
Xie Fang, Feng Changhong, Wang Zhaoxing, et al. Improved Structure Design of Belt Wheel in Automobile Engine Water Pump[J]. Journal of Mechanical Strength, 2014, 36(2): 285-289.
[2]刘健，仇性启，薄万顺, 等. 橡胶O形密封圈最大接触压力数值分析[J]. 润滑与密封, 2010, 35(1): 41-44.
Liu Jian, Qiu Xingqi, Bo Wanshun, et al. Numerical Analysis on the Maximum Contact Pressure of Rubber O-Ring[J]. Lubrication Engineering, 2010, 35(1): 41-44.
[3]杨光，胡旭林，崔盼超. Yx形密封圈应力与变形非线性有限元分析[J]. 煤矿机械, 2010， 31(3):99-101.
Yang Guang, Hu Xulin, Cui Panchao. Nonlinear Finite Element Analysis of Stress and Deformation on Rubber Sealing Yx-Ring Section[J]. Coal Mine Machinery, 2010, 31(3):99-101.
[4]李振涛，孙鑫晖，张玉满，等. O形密封圈密封性能非线性有限元数值模拟[J]. 润滑与密封, 2011, 36(9): 86-90.
Li Zhentao, Sun Xinhui, Zhang Yuman, et al. Finite Element Numerical Simulation of the Sealing Performance of O-ring Seals[J]. Lubrication Engineering, 2011, 36(9): 86-90.
[5]高九阳，喻九阳，王成刚，等. 沟槽对O形圈密封结构性能的影响[J]. 武汉工程大学学报, 2010, 32(7): 78-80.
Gao Jiuyang, Yu Jiuyang, Wang Chenggang, et al. Effects of Grooves on Sealing Performance of O-ring Seal Structure[J]. Journal of Wuhan Institute of Technology, 2010, 32(7): 78-80.
[6]于润生，杨秀萍. Yx形液压密封圈的有限元分析及结构优化[J]. 润滑与密封, 2011, 36(7): 66-69.
Yu Runsheng, Yang Xiuping. Finite Element Analysis and Optimization Design of Yx Shape Hydraulic Sealing Ring[J]. Lubrication Engineering, 2011, 36(7): 66-69.
[7]张东葛，张付英，王世强. 基于ANSYS的Y型密封圈结构和工作参数的优化设计[J]. 润滑与密封, 2012, 37(11): 87-90.
Zhang Dongge, Zhang Fuying, Wang Shiqiang. The Optimization Design for Structure and Operating Parameters of Y Sealing Ring Based on ANSYS[J]. Lubrication Engineering, 2012, 37(11): 87-90.
[8]于润生. 液压密封圈有限元分析与研究[D]. 天津：天津理工大学，2012.
[9]Johnson K L. Contact Mechanics [M]. Cambridge，UK: Cambridge University Press, 1985.

[1]	吴怀超, 吴白羽, 张秀华. 石蜡感温阀传热性能的数字仿真研究 [J]. J4, 201016, 21(16): 1921-1926.
[2]	王晓铭1;张建超1;王绪平2;张彦彬2;罗亮3;赵伟4;刘波5;聂晓霖6;李长河1. 不同冷却工况下的磨削钛合金温度场模型及验证[J]. 中国机械工程, 2021, 32(05): 572-578,586.
[3]	李广琪1;朱刚贤1;王丽芳2;赵亮1;石世宏1. 离焦量对中空环形激光熔覆层温度场及应力场的影响[J]. 中国机械工程, 2021, 32(05): 587-593,599.
[4]	唐斌, 范志勇, 项载毓, 吴元科, 黄博, 莫继良, . [轮轨磨耗及预测]高速列车制动摩擦块切入端特征对制动界面特性的影响[J]. 中国机械工程, 2021, 32(04): 412-419.
[5]	董永刚, 仪帅, 黄鑫磊, 宋剑锋, 杜晓钟. [轮轨磨耗及预测]列车紧急制动过程中踏面温度分布及磨耗预测[J]. 中国机械工程, 2021, 32(04): 431-438,445.
[6]	陈汇龙;桂铠;李新稳;韩婷;谢晓凤;陆俊成. 工况参数对机械密封液膜汽化特性及性能的影响[J]. 中国机械工程, 2021, 32(01): 2-11.
[7]	高健;赵自强;王文中. 基于热四极法的涂层刀具切削温度分布研究[J]. 中国机械工程, 2020, 31(19): 2316-2321.
[8]	黄仁凯;戴宁;程筱胜. 基于选区激光熔化温度场数值模拟的支撑结构优化[J]. 中国机械工程, 2020, 31(19): 2346-2354.
[9]	张高峰;龚俊明;李景焘;谢国广;孙昊. 形貌重构砂轮磨削试验研究[J]. 中国机械工程, 2020, 31(12): 1420-1424,1436.
[10]	张静;马靓;赵登飞. 大方坯结晶器电磁搅拌器结构优化[J]. 中国机械工程, 2020, 31(10): 1148-1154.
[11]	胡金花1;宋凯2;熊礼明3. 考虑修正平均等效应力强度因子的焊点缺陷疲劳寿命研究[J]. 中国机械工程, 2020, 31(06): 740-745.
[12]	彭锐涛1;吴艳萍1;唐新姿1;鲁鑫焱1;胡云波2. 流道出口位置对加压内冷却砂轮磨削性能的影响[J]. 中国机械工程, 2020, 31(04): 489-497.
[13]	方修洋;黄伟;王俊国. 温度对动车组车轮钢服役次生疲劳裂纹起裂扩展特性影响[J]. 中国机械工程, 2020, 31(03): 261-266.
[14]	倪敬1,2;史雨1,2;蒙臻1,2;黄浩锋1. 单回路保护阀密封圈表界面黏附特性[J]. 中国机械工程, 2019, 30(24): 2899-2905.
[15]	崔云先1;牟瑜1;王成勇2;郑李娟2;殷俊伟1;薛生俊1. 采用薄膜热电偶的多层印刷电路板原位钻削温度测量[J]. 中国机械工程, 2019, 30(22): 2655-2660.