轴对称拉深成形法兰区起皱失稳变形能及临界压边力

中国机械工程 ›› 2013, Vol. 24 ›› Issue (23): 3244-3248.

轴对称拉深成形法兰区起皱失稳变形能及临界压边力

秦泗吉;梁韶伟;张树栋

燕山大学先进锻压技术与科学教育部重点实验室，秦皇岛，066004

出版日期:2013-12-10 发布日期:2013-12-06
基金资助:
国家自然科学基金资助项目(51175451)；河北省自然科学基金资助项目（E2010001216）

Strain Energy and Critical BHF of Flange Wrinkling Instability in Axisymmetric Deep Drawing Process

Qin Siji;Liang Shaowei;Zhang Shudong

Key Laboratory of Advanced Forging & Stamping Technology and Science of Ministry of Education,Yanshan University, Qinhuangdao, Hebei, 066004

Online:2013-12-10 Published:2013-12-06
Supported by:
National Natural Science Foundation of China（No. 51175451）;Hebei Provincial Natural Science Foundation of China（No. E2010001216）

摘要/Abstract

摘要：

在平面应变假设条件下，对轴对称拉深成形法兰区的起皱失稳问题进行了理论分析。首先采用数学方法，将以积分形式表示的应力解析式进行了简化。在此基础上，进一步简化了起皱过程中变形能的计算式。给出的算例表明，对起皱过程中的变形能分别以简化后的计算式和以原积分式进行计算，其结果误差很小，相对误差小于0.8%。该起皱失稳临界压边力的计算和分析简化方法有助于给出简明和符合实际的起皱判据。

关键词: 轴对称拉深, 临界压边力, 变形能, 起皱

Abstract:

In the condition of the plane strain hypothesis, flange wrinkling instability of the sheet metal in axisymmetric deep drawing was analyzed theoretically. At first, stress formula in integral form was simplified by mathematical method. On the basis of that, the calculation of the strain energy was simplified. Given examples show that the calculation results by simplified formula are close to that by original integral one. The maximum relative error is less than 0.8%. Finally, a simplified formula for calculation of critical BHF of wrinkling instability was given. It is helpful to provide concise and realistic wrinkling criterion.

Key words: axisymmetric deep drawing process, critical blank holding force(BHF), strain energy, wrinkle

中图分类号:

TG386.41

秦泗吉, 梁韶伟, 张树栋. 轴对称拉深成形法兰区起皱失稳变形能及临界压边力[J]. 中国机械工程, 2013, 24(23): 3244-3248.

Qin Siji, Liang Shaowei, Zhang Shudong. Strain Energy and Critical BHF of Flange Wrinkling Instability in Axisymmetric Deep Drawing Process[J]. China Mechanical Engineering, 2013, 24(23): 3244-3248.

[1]	詹梅, 雷煜东, 郑泽邦, . [成形过程仿真优化与集成计算材料工程]集成计算材料工程在精确塑性成形中的应用现状与发展趋势[J]. 中国机械工程, 2020, 31(22): 2663-2677.
[2]	姚梓萌, 李言, 杨明顺, 张敬冲, 张成兴. 基于响应面法的单点增量成形过程变形能优化[J]. 中国机械工程, 2017, 28(07): 862-866.
[3]	孔晓华, 秦泗吉, 陆宏, 郑星. 圆锥形凹模径向分块压边拉深工艺实验研究[J]. 中国机械工程, 2015, 26(18): 2528-2532,2538.
[4]	刘迪辉, 林成业. 温度对薄板抗起皱性能的影响[J]. 中国机械工程, 2015, 26(10): 1395-1398.
[5]	秦泗吉, 杨莉, 盖玢玢. 平面应力条件下轴对称拉深成形法兰区起皱和破裂分析[J]. 中国机械工程, 2014, 25(23): 3221-3226.
[6]	秦泗吉1, 2, 黄晓忠3, 王婧4. 径向分块双压边圈轴对称拉深成形工艺研究 [J]. 中国机械工程, 2011, 22(14): 1741-1744.
[7]	张华. 等效拉深筋精细数值化模型与起皱模拟应用 [J]. 中国机械工程, 2010, 21(21): 2624-2627.