预成形管坯压制成形汽车桥壳的变形分析

中国机械工程 ›› 2013, Vol. 24 ›› Issue (19): 2670-2674.

预成形管坯压制成形汽车桥壳的变形分析

王连东;杨东峰;崔亚平;陈国强

燕山大学，秦皇岛，066004

出版日期:2013-10-10 发布日期:2013-10-11
基金资助:
河北省自然科学基金资助项目（E2012203022）
Hebei Provincial Natural Science Foundation of China（No. E2012203022）

Deformation Analysis of Automobile Housings Pressed and Formed by Pre-formed Tube

Wang Liandong;Yang Dongfeng;Cui Yaping;Chen Guoqiang

Yanshan University,Qinhuangdao,Hebei,066004

Online:2013-10-10 Published:2013-10-11
Supported by:
Hebei Provincial Natural Science Foundation of China（No. E2012203022）

摘要/Abstract

摘要：

介绍了小型汽车桥壳样件胀压成形的工艺，针对两端经过缩径、中部经过液压胀形得到的轴对称状预成形管坯，其内部充液后用模具压制成形桥壳样件的过程，定性分析了横截面、纵截面的变形，揭示了变形机理以及壁厚的变化规律，探讨了桥包部分横截面大小对其成形性的影响。通过有限元模拟和工艺试验，进一步考察了管坯压制成形工艺的成形性，并定量分析了壁厚的分布情况。研究结果表明：轴对称状的预成形管坯压制成形异型截面的汽车桥壳样件时，样件成形性好，壁厚分布较好，成形过程中所需液体压力低。

关键词: 汽车桥壳, 胀压成形工艺, 预成形管坯, 变形分析, 壁厚分布

Abstract:

A bulging-pressing compound-deforming technology was introduced for some kind of small automobile axle housings. The deformation on the chosen crossing and longitudinal sections was analyzed qualitatively for pressing the pre-formed tube of axisymmetric shape by the die after it was charged with liquid. The deformation pattern and the change of wall thickness was discovered, and the effects of forming property resulted from the size of crossing section in the axle housing cover part were discussed. Through the FEM simulation and test, the forming property of pressing the tube is deeply inspected, and the wall thickness distribution is quantitatively analyzed. It is founded that when the automobile axle housing of special shaped cross-sections is pressed from the pre-formed tube, the trial samples possesses of good formability, better wall thickness distribution, and lower internal pressure.

Key words: automobile housing, bulging-pressing compound-deforming technology, pre-formed tube, deformation analysis, wall thickness distribution

中图分类号:

TG316

王连东;杨东峰;崔亚平;陈国强. 预成形管坯压制成形汽车桥壳的变形分析[J]. 中国机械工程, 2013, 24(19): 2670-2674.

Wang Liandong;Yang Dongfeng;Cui Yaping;Chen Guoqiang. Deformation Analysis of Automobile Housings Pressed and Formed by Pre-formed Tube[J]. China Mechanical Engineering, 2013, 24(19): 2670-2674.

[1]	吴娜, 王连东, 沈亚坤, 张蒙. 充液压制成形汽车桥壳后盖区开裂分析及预成形管坯形状优化设计[J]. 中国机械工程, 2016, 27(23): 3246-3251.
[2]	王连东, 徐永生, 陈旭静, 吴娜, . 小型桥壳液压胀形初始变形条件分析及成形试验[J]. 中国机械工程, 2016, 27(03): 398-402.
[3]	王连东;庞蒙;周立凤;崔亚平. 中型卡车胀压成形桥壳预成形管坯的设计及成形分析[J]. 中国机械工程, 2015, 26(12): 1684-1689.
[4]	崔亚平, 王连东, 杨立云, 刘超. 附加前盖对汽车桥壳胀-压成形性的影响[J]. 中国机械工程, 2013, 24(13): 1831-1835.
[5]	梁晨, 刘唯唯, 陈国强, 苏明凯, 王连东. 半滑动式液压胀形汽车桥壳的数值模拟及成形实验 [J]. 中国机械工程, 2012, 23(4): 479-484.
[6]	崔亚平, 王连东, 杨立云, 杨东峰. 胀-压复合成形汽车桥壳预成形管坯的设计及成形试验[J]. 中国机械工程, 2012, 23(21): 2577-2580.
[7]	王连东, 陈国强, 杨东峰, 韩晓亮. 普通液压机半滑动式液压胀形汽车桥壳的工艺研究 [J]. 中国机械工程, 2011, 22(18): 2249-2252.