材料晶界和晶粒对电火花微细加工的影响研究

中国机械工程 ›› 2011, Vol. 22 ›› Issue (13): 1601-1604.

材料晶界和晶粒对电火花微细加工的影响研究

李剑忠;沈飞虎;殷国强;余祖元

大连理工大学,大连,116024

出版日期:2011-07-10 发布日期:2011-07-14
基金资助:
国家自然科学基金资助项目(50775020)；国家高技术研究发展计划(863计划)资助项目(2009AA044205-1)
National Natural Science Foundation of China（No. 50775020）;
National High-tech R&D Program of China (863 Program) （No. 2009AA044205-1）

Study on Influences of Grain Boundary and Grain on Machining Performance of Micro-EDM

Li Jianzhong;Shen Feihu;Yin Guoqiang;Yu Zuyuan

Dalian University of Technology, Dalian, 116024

Online:2011-07-10 Published:2011-07-14
Supported by:

National Natural Science Foundation of China（No. 50775020）;
National High-tech R&D Program of China (863 Program) （No. 2009AA044205-1）

摘要/Abstract

摘要：

为了在电火花微细加工中确定合理的工具损耗补偿工艺与加工工艺,提高微小零件微细加工的质量,通过在合金材料上选择晶粒和晶界部位大量加工微孔以及其后的统计分析,研究了微细电火花加工过程中工件材料晶粒与晶界对放电间隙、材料去除速度以及电极体积相对损耗等加工特性的影响。研究结果表明,由于工件材料中晶粒和晶界在成分、熔点、热导率以及机械性能等方面的差异,当用微细电火花进行微细加工,特别是当加工尺度小于工件材料的晶粒尺寸时,晶粒和晶界的加工特性具有明显差别,制订工具损耗补偿工艺和加工工艺时应该考虑到材料微观结构对加工过程的影响。

关键词:

微细电火花, 微细加工, 晶粒, 晶界

Abstract:

In micro EDM, in order to select reasonable machining parameters to compensate the tool wear and to improve the quality of machined micro feature, a statistical analysis was used to study the influences of grain and grain boundary of the workpiece material on the material removal rate, tool wear ratio and the discharge gap by drilling micro holes in grain and grain boundary of the alloy. Due to the material characteristic difference between grain and grain boundary, such as composition, melting point, thermal conductivity and mechanical properties, the results vary. When the size of a machined feature is smaller than the grain size of the materials, the machining performance of grain and the grain boundary are different. Therefore, it is necessary to take micro structure of workpiece material into account when the tool wear is compensated. 

Key words: micro electrical discharge machining(EDM), micro machining, grain, grain boundary

中图分类号:

TG661
TG113

李剑忠, 沈飞虎, 殷国强, 余祖元.

材料晶界和晶粒对电火花微细加工的影响研究

[J]. 中国机械工程, 2011, 22(13): 1601-1604.

LI Jian-Zhong, CHEN Fei-Hu, YAN Guo-Jiang, TU Jie-Yuan.

Study on Influences of Grain Boundary and Grain on Machining Performance of Micro-EDM

[J]. China Mechanical Engineering, 2011, 22(13): 1601-1604.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: http://www.cmemo.org.cn/CN/

http://www.cmemo.org.cn/CN/Y2011/V22/I13/1601

[1]	王国彪, 赖一楠, 范大鹏, 杨华勇, 王时龙. 新型精密传动机构设计与制造综述 [J]. J4, 201016, 21(16): 1891-1897.
[2]	王立存, 陈进, 张贤明, 陈国强. 基于泛函的制冷涡旋压缩机变壁厚涡旋型线理论及形状优化 [J]. J4, 201016, 21(16): 1898-1901.
[3]	李小力, 陈威, 闫蓉. 基于BP神经网络的空间轮廓误差自适应补偿 [J]. J4, 201016, 21(16): 1902-1906.
[4]	夏瑞雪, 卢荣胜, 刘宁, 董敬涛. 基于圆点阵列靶标的特征点坐标自动提取方法 [J]. J4, 201016, 21(16): 1906-1910.
[5]	陈立锋, 吴晓铃, 秦大同, 肖正明. 齿轮啮合过程摩擦功耗研究 [J]. J4, 201016, 21(16): 1911-1915.
[6]	李明磊, 贾育秦, 张学良, 刘丽琴, 杜娟, 温淑花, 兰国生. 基于多目标差异演化算法的并联机构结构优化 [J]. J4, 201016, 21(16): 1915-1920.
[7]	吴怀超, 吴白羽, 张秀华. 石蜡感温阀传热性能的数字仿真研究 [J]. J4, 201016, 21(16): 1921-1926.
[8]	鲁开讲, 师俊平, 张锋涛. 平面三自由度并联机构动力学优化设计 [J]. J4, 201016, 21(16): 1926-1931.
[9]	张敏杰, 王庆九, 管成. 并联式油液混合动力挖掘机动力系统仿真研究 [J]. J4, 201016, 21(16): 1932-1936.
[10]	刘安平, 刘济春. IPC-208B型原子力显微镜大范围扫描三维驱动系统研究 [J]. J4, 201016, 21(16): 1936-1940.
[11]	姚运萍, 王智渊. 螺栓连接受载能量损失与结合面参数识别 [J]. J4, 201016, 21(16): 1941-1943,1951.
[12]	陈建, 邓利娟. 恒力弹性机构的设计 [J]. J4, 201016, 21(16): 1944-1946.
[13]	罗洁思, 于德介, 史美丽. 基于SVD和线调频小波路径追踪的转速波动齿轮箱故障诊断 [J]. J4, 201016, 21(16): 1947-1951.
[14]	战晓磊, 辛洪兵, 汉斯·彼德　兰特斯. 基于虚拟现实的MOTOMAN-HP3型机器人运动学仿真 [J]. J4, 201016, 21(16): 1952-1954,1998.
[15]	苏厚军, 史铁林, 陈非. 高炉煤气透平机状态检修的设计与实施 [J]. J4, 201016, 21(16): 1955-1958.