大型复杂产品分层网络计划模型

中国机械工程 ›› 2010, Vol. 21 ›› Issue (05): 540-544.

大型复杂产品分层网络计划模型

徐建萍1,2;郭;钢1;罗妤1,3;李浩1

1.重庆大学,重庆,400044

2.贵州大学,贵阳,5500083.重庆科技学院,重庆,400050

出版日期:2010-03-10 发布日期:2010-03-22
基金资助:
国家863高技术研究发展计划资助项目(2007AA04Z1B1)
National High-tech R&D Program of China (863 Program) （No. 2007AA04Z1B1）

Research on Layered Network Planning Model Based on Large-scale and Complex Products

Xu Jianping1,2;Guo Gang1;Luo Yu1,3;Li Hao1

1.Chongqing University,Chongqing,400044

2.Guizhou University,Guiyang,550003

3.Chongqing University of Science and Technology, Chongqing,400050

Online:2010-03-10 Published:2010-03-22
Supported by:
National High-tech R&D Program of China (863 Program) （No. 2007AA04Z1B1）

摘要/Abstract

摘要：

深入研究了大型复杂产品生产的特点,采用装配单元来优化产品装配物料清单,提出了面向装配单元和装配序列的可扩展两级网络计划应用模式。通过装配单元来指导产品设计和零部件的生产准备;利用工序进装点来控制零部件的成套性。分层的网络计划模式增强了上层计划的稳定性,提高了底层装配序列计划执行和调整的灵活性。该计划模式已在项目制造管理平台上实现,正投入示范应用。

关键词:

大型复杂产品, 装配单元, 分层网络计划, 装配序列

Abstract:

Based on deep analysis of the characteristics in the assembly process of large-scale and complex products, this paper proposed a way of optimizing assembly bill of material(ABOM) by assembly cell. On this basis a mode of extensible layered network planning for assembly cell and assembly sequence was provided. The mode can supervise the production arrangement of components based on assembly cell, and supervised complete set of components of under assembly operation entrance. Through layered network planning the stability of upper production planning can be enhanced, at the same time the flexibility of performance and adjustment for underlying assembly sequence schedule can be advanced. Now the layered planning mode has implemented under software platform of project management.

Key words: large-scale and complex product, assembly cell, layered network planning, assembly sequence

中图分类号:

F272

徐建萍, 郭, 钢, 罗妤, 李浩.

大型复杂产品分层网络计划模型

[J]. 中国机械工程, 2010, 21(05): 540-544.

XU Jian-Ping, GUO,GANG,LUO Yu, LI Gao.

Research on Layered Network Planning Model Based on Large-scale and Complex Products

[J]. China Mechanical Engineering, 2010, 21(05): 540-544.

[1]	王国彪, 赖一楠, 范大鹏, 杨华勇, 王时龙. 新型精密传动机构设计与制造综述 [J]. J4, 201016, 21(16): 1891-1897.
[2]	王立存, 陈进, 张贤明, 陈国强. 基于泛函的制冷涡旋压缩机变壁厚涡旋型线理论及形状优化 [J]. J4, 201016, 21(16): 1898-1901.
[3]	李小力, 陈威, 闫蓉. 基于BP神经网络的空间轮廓误差自适应补偿 [J]. J4, 201016, 21(16): 1902-1906.
[4]	夏瑞雪, 卢荣胜, 刘宁, 董敬涛. 基于圆点阵列靶标的特征点坐标自动提取方法 [J]. J4, 201016, 21(16): 1906-1910.
[5]	陈立锋, 吴晓铃, 秦大同, 肖正明. 齿轮啮合过程摩擦功耗研究 [J]. J4, 201016, 21(16): 1911-1915.
[6]	李明磊, 贾育秦, 张学良, 刘丽琴, 杜娟, 温淑花, 兰国生. 基于多目标差异演化算法的并联机构结构优化 [J]. J4, 201016, 21(16): 1915-1920.
[7]	吴怀超, 吴白羽, 张秀华. 石蜡感温阀传热性能的数字仿真研究 [J]. J4, 201016, 21(16): 1921-1926.
[8]	鲁开讲, 师俊平, 张锋涛. 平面三自由度并联机构动力学优化设计 [J]. J4, 201016, 21(16): 1926-1931.
[9]	张敏杰, 王庆九, 管成. 并联式油液混合动力挖掘机动力系统仿真研究 [J]. J4, 201016, 21(16): 1932-1936.
[10]	刘安平, 刘济春. IPC-208B型原子力显微镜大范围扫描三维驱动系统研究 [J]. J4, 201016, 21(16): 1936-1940.
[11]	姚运萍, 王智渊. 螺栓连接受载能量损失与结合面参数识别 [J]. J4, 201016, 21(16): 1941-1943,1951.
[12]	陈建, 邓利娟. 恒力弹性机构的设计 [J]. J4, 201016, 21(16): 1944-1946.
[13]	罗洁思, 于德介, 史美丽. 基于SVD和线调频小波路径追踪的转速波动齿轮箱故障诊断 [J]. J4, 201016, 21(16): 1947-1951.
[14]	战晓磊, 辛洪兵, 汉斯·彼德　兰特斯. 基于虚拟现实的MOTOMAN-HP3型机器人运动学仿真 [J]. J4, 201016, 21(16): 1952-1954,1998.
[15]	苏厚军, 史铁林, 陈非. 高炉煤气透平机状态检修的设计与实施 [J]. J4, 201016, 21(16): 1955-1958.