晶体已加工表面频率特征对亚表层温度场的影响

doi:10.3969/j.issn.1004-132X.2022.16.012

摘要/Abstract

摘要： 为了更加准确地分析表面形貌对KH2PO4(KDP)晶体元件激光损伤和使用性能的影响，通过功率谱密度和连续小波变换对KDP晶体已加工表面存在的实际频率特征进行提取和重构。利用波动光学理论分析经入射波长1.064 μm、功率20 MW/μm2的激光束照射1 ns后，表面频率特征对KDP晶体亚表层光场及温度场的影响。结果表明，当表面频率特征的波长越接近入射光波长1.064 μm，KDP晶体亚表层的光场畸变现象越严重，会造成局部聚焦，温度越高；当波长超过20 μm时，在振幅不变的情况下，最高温度随着波长的增加基本不变。通过切削实验获得的KDP晶体已加工表面上明显存在的波长分别为14 μm、50 μm和140 μm，对KDP晶体亚表层造成的温升分别为56 K、22 K和12 K。当波长相同时，KDP晶体的最高温度与表面频率幅值成线性关系。随着表面频率波长的增加，温度最高点的位置向KDP晶体内部延伸。

关键词: 已加工表面, 波长, 振幅, KDP晶体, 光场, 温度场

Abstract: To analyze the influences of surfaces topography on the laser damage and performance of KH2PO4（KDP） crystal, the frequency features of machined surface KDP crystal surfaces were extracted and reconstructed by power spectral density and continuous wavelet transform. Wave optics theory was used to analyze the influences of frequency features on the subsurface light temperature fields of KDP crystals irradiated by 1.064 μm laser wavelength with the power of 20 MW/μm2 for 1ns. The results show that temperature of KDP crystals becomes larger with wavelength of surface frequencies closer to incident laser wavelength(1.064 μm). If the wavelength is over 20 μm, temperature of KDP crystals is unchanged with the changing of frequency features. The obvious wavelengths on the machined surface of KDP crystals obtained by cutting experiments are as 14 μm, 50 μm and 140 μm respeclively, and the subsurface temperature of KDP crystals affected by these frequency features rises are as 56 K, 22 K and 12 K. Maximum temperature of KDP crystals increases with the increasing of amplitude under the same wavelength. With the increasing of surface frequency wavelength, the position of the maximum temperature extends to the interior of the KDP crystals.

Key words: , machined surface, wavelength, amplitude, KH2PO4(KDP) crystal, light field, temperature field

中图分类号:

TG161.14

束梓豪, 庞启龙, 况良杰. 晶体已加工表面频率特征对亚表层温度场的影响[J]. 中国机械工程, 2022, 33(16): 1983-1991.

SHU Zihao, PANG Qilong, KUANG Liangjie. Effects of Frequency Features Generated in Machined Surface on Subsurface Temperature Field of KH2PO4 Crystals[J]. China Mechanical Engineering, 2022, 33(16): 1983-1991.

参考文献

［1］WANG X, GAO H, YUAN J L. Experimental Investigation and Analytical Modelling of the Tool Influence Function of the Ultra-precision Numerical Control Polishing Method Based on the Water Dissolution Principle for KDP Crystals［J］. Precision Engineering—Journal of the International Societies for Precision Engineering and Nanotechnology, 2020, 65:185-196.
［2］谢晓义，朱茂东，王斌，等. γ射线辐照快速生长KDP晶体的性能［J］. 中国激光, 2018, 45(10):149-155.
XIE Xiaoyi, ZHU Maodong, WANG Bin, et al. The Properties of Rapid Growth of KDP Crystals Irradiated by Gamma Rays［J］. Chinese Journal of Lasers, 2018, 45(10):149-155.
［3］冉钰庭，黄宏彪，尹进，等. 单点金刚石飞切KDP晶体表面缺陷深度的研究［J］. 光子学报, 2017, 46(5):26-32.
RAN Yuting, HUANG Hongbiao, YIN Jin, et al. Study on the Surface Defect Depth of Single-point Diamond Fly-cut KDP Crystals［J］. Acta Photonica Sinica, 2017, 46(5):26-32.
［4］SPAETH M L, MANES K R, KALANTAR D H, et al. Description of the NIF Laser［J］. Fusion Science and Technology, 2016, 69(1):25-145.
［5］PEI G Q, YE L, DU W F, et al. Optimization of Second-harmonic Generation in Large-aperture KDP Crystals Using Multipoint Support Mounting Configurations［J］. Optical Engineering, 2020, 59(1):016104.
［6］邵建达，戴亚平，许乔. 惯性约束聚变激光驱动装置用光学元器件的研究进展［J］. 光学精密工程, 2016, 24(12):2889-2895.
SHAO Jianda, DAI Yaping, XU Qiao. ResearchProgress of Optical Components for Inertial Confinement Fusion Laser Driving Device［J］. Optics and Precision Engineering, 2016, 24(12):2889-2895.
［7］邹洋，赵丽丽，游丽君，等. TiO2热控涂层激光辐照特性研究［J］. 表面技术, 2019, 48(6):189-194.
ZOU Yang, ZHAO Lili, YOU Lijun, et al. Study on the Laser Irradiation Characteristics of TiO2 Thermal Control Coating［J］. Surface Technology, 2019, 48(6):189-194.
［8］TAN C, ZHAO L J, CHEN M J, et al. Experimental and Theoretical Investigation of Localized CO2 Laser Interaction with Fused Silica during the Process of Surface Damage Mitigation［J］. Results in Physics, 2020, 16:102936.
［9］郭文华，陶冶，张蓉竹. 表面划痕中残余抛光颗粒对材料热损伤特性的影响［J］. 强激光与粒子束, 2020, 32(3):45-49.
GUO Wenhua, TAO Ye, ZHANG Rongzhu. The Influence of Residual Polishing Particles in Surface Scratches on the Thermal Damage Characteristics of Materials［J］. High Power Laser and Particle Beams, 2020, 32(3):45-49.
［10］YIN H W, LI M W, HUANG J, et al. Growth Study and Characterization of KDP Crystals Grown by 2D Translation Method［J］. Materials Chemistry and Physics, 2018, 215:168-175.
［11］黄萍萍，王端良，李伟东，等. 温度不均匀引起KDP晶体开裂的实验与模拟［J］. 硅酸盐学报, 2018, 46(7):929-937.
HUANG Pingping, WANG Duanliang, LI Weidong, et al. Experiment and Simulation of KDP Crystal Cracking Caused by Uneven Temperature［J］. Journal of the Chinese Ceramic Society, 2018, 46(7):929-937.
［12］刘峣，武玉琳，屈云鹏，等. Ba2+在KDP(100)表面吸附的密度泛函理论研究［J］. 材料工程, 2019, 47(11):123-127.
LIU Yao, WU Yulin, QU Yunpeng, et al. Density Functional Theory Study of Ba2+ Adsorption on KDP(100) Surface［J］. Journal of Materials Engineering, 2019, 47(11):123-127.
［13］BAIG M I, ANIS M, MULEY G G. Comprehensive Study on Crystal Growth, Optical and Dielectric Properties of Potassium Dihydrogen Orthophosphate Crystal Influenced by Organic Additive Salicylic Acid［J］. Optik, 2017, 131:165-170.
［14］秦梦飞，许心光，王波，等. 不同生长方式和籽晶切向KDP晶体的生长及性能［J］. 光学精密工程, 2019, 27(3):511-516.
QIN Mengfei, XU Xinguang, WANG Bo, et al. Growth and Properties of KDP Crystals with Different Growth Methods and Seed Tangential Direction［J］. Optics and Precision Engineering, 2019, 27(3):511-516.
［15］李伟东，王圣来，于光伟，等. 过饱和度对KDP晶体生长及表面形貌的影响［J］. 硅酸盐学报, 2017, 45(7):955-960.
LI Weidong, WANG Shenglai, YU Guangwei, et al. The Effect of Supersaturation on KDP Crystal Growth and Surface Morphology［J］. Journal of the Chinese Ceramic Society, 2017, 45(7):955-960.
［16］张浩，孙见君，马晨波，等. 机械密封端面形貌的三维重建及其表征［J］. 中国机械工程, 2017, 28(11):1287-1291.
ZHANG Hao, SUN Jianjun, MA Chenbo, et al. Three-dimensional Reconstruction and Characterization of the End Face of Mechanical Seal［J］. China Mechanical Engineering, 2017, 28(11):1287-1291.
［17］孙见君，张凌峰，於秋萍，等. 基于粗糙表面分形表征新方法的结合面法向接触刚度模型［J］. 振动与冲击, 2019, 38(7):212-217.
SUN Jianjun, ZHANG Lingfeng, YU Qiuping, et al. The Normal Contact Stiffness Model of the Joint Surface Based on a New Method of Rough Surface Fractal Characterization［J］. Journal of Vibration and Shock, 2019, 38(7):212-217.
［18］GEORG S, DUENOW U, SEITZ H. Effect of Laser Pulse Overlap and Scanning Line Overlap on Femtosecond Laser-structured Ti6Al4V Surfaces［J］. Materials, 2020, 13(4):969.
［19］阳红，王宝瑞，吉方，等. KDP晶体单点金刚石飞切轨迹波纹误差辨识研究［J］.振动·测试与诊断, 2017, 37(2):235-239.
YANG Hong, WANG Baorui, JI Fang, et al. Research on Ripple Error Identification of KDP Crystal Single Point Diamond Flying-cut Trajectory［J］. Journal of Vibration, Measurement & Diagnosis, 2017, 37(2):235-239.
［20］MIAO J G, YU D P, AN C H, et al. Investigation on the Generation of the Medium-frequency Waviness Error in Flycutting Based on 3D Surface Topography［J］. International Journal of Advanced Manufacturing Technology, 2017, 90(1/4):667-675.
［21］CHEN W Q, LIANG Y C, SUN Y Z, et al. Investigation on the Influence of Machine Tool Dynamics on the Wavefront Gradient of KH2PO4 Crystals［J］. Journal of Manufacturing Science and Engineering, 2014, 136(5):051006.
［22］PRABHAKAR D V N, KUMAR M S, KRISHNA A G. A Novel Hybrid Transform Approach with Integration of Fast Fourier, Discrete Wavelet and Discrete Shearlet Transforms for Prediction of Surface Roughness on Machined Surfaces［J］. Measurement, 2020, 164:108011.
［23］石爱娟,叶丹. 平面磨削表面的特征解耦与形貌仿真［J］. 中国测试, 2021, 47(5):46-51.
SHI Aijuan, YE Dan. Feature Decoupling and Topography Simulation of Surface Grinding Surface［J］. China Measurement & Test, 2021, 47(5):46-51.
［24］王贵林. KDP光学零件超精密车削加工误差的频谱特性与控制［J］. 应用光学, 2017, 38(2):159-164.
WANG Guilin. Spectrum Characteristics and Control of Machining Errors in Ultra-precision Turning of KDP Optical Parts［J］. Applied Optics, 2017, 38(2):159-164.
［25］CHENG J, YANG H, LIU Q, et al. Characterization of Manufacturing-induced Surface Scratches and Their Effect on Laser Damage Resistance Performance of Diamond Fly-cut KDP Crystal［J］. Results in Physics, 2019, 15:102753.
［26］陈明君，李明全，姜文斌，等. 基于傅里叶模方法的KDP晶体镀膜减反技术［J］. 强激光与粒子束, 2011, 23(2):412-418.
CHEN Mingjun, LI Mingquan, JIANG Wenbin, et al. KDP Crystal Coating Anti-reflection Technology Based on Fourier Mode Method［J］. High Power Laser and Particle Beams, 2011, 23(2):412-418.
［27］任寰，姜宏振，刘旭，等. 划痕型缺陷对光场质量的影响［J］. 强激光与粒子束, 2014, 26(9):198-204.
REN Huan, JIANG Hongzhen, LIU Xu, et al. TheInfluence of Scratch-type Defects on the quality of Light Field［J］. High Power Laser and Particle Beams, 2014, 26(9):198-204.
［28］YANG H, CHENG J, LIU Z C, et al. Dynamic Behavior Modeling of Laser-induced Damage Initiated by Surface Defects on KDP Crystals under Nanosecond Laser Irradiation［J］. Scientific Reports, 2020, 10(1):500.
［29］CHENG J, XIAO Y, LIU Q, et al. Effect of Surface Scallop Tool Marks Generated in Micro-milling Repairing Process on the Optical Performance of Potassium Dihydrogen Phosphate Crystal［J］. Materials & Design, 2018, 157:447-456.［30］LIU Q, CHENG J, LIAO Z R, et al. Incident Laser Modulation by Tool Marks on Micro-milled KDP Crystal Surface:Numerical Simulation and Experimental Verification［J］. Optics and Laser Technology, 2019, 119:105610.
［31］CHENG J, CHEN M J, KAFKA K, et al. Determination of Ultra-short Laser Induced Damage Threshold of KH2PO4 Crystal:Numerical Calculation and Experimental Verification［J］. AIP Advances, 2016, 6(3):035221.

[1]	吴怀超, 吴白羽, 张秀华. 石蜡感温阀传热性能的数字仿真研究 [J]. J4, 201016, 21(16): 1921-1926.
[2]	余国达, 刘怀举, 卢泽华, 魏沛堂. 脂润滑条件下塑料齿轮稳态温度场仿真与试验研究[J]. 中国机械工程, 2022, 33(08): 890-898，907.
[3]	许明三, 周春辉, 张正, 曾寿金, . 激光熔覆过程中的粉、气、光耦合温度场[J]. 中国机械工程, 2022, 33(01): 70-77.
[4]	王晓铭1;张建超1;王绪平2;张彦彬2;罗亮3;赵伟4;刘波5;聂晓霖6;李长河1. 不同冷却工况下的磨削钛合金温度场模型及验证[J]. 中国机械工程, 2021, 32(05): 572-578,586.
[5]	李广琪1;朱刚贤1;王丽芳2;赵亮1;石世宏1. 离焦量对中空环形激光熔覆层温度场及应力场的影响[J]. 中国机械工程, 2021, 32(05): 587-593,599.
[6]	董永刚, 仪帅, 黄鑫磊, 宋剑锋, 杜晓钟. [轮轨磨耗及预测]列车紧急制动过程中踏面温度分布及磨耗预测[J]. 中国机械工程, 2021, 32(04): 431-438,445.
[7]	黄仁凯;戴宁;程筱胜. 基于选区激光熔化温度场数值模拟的支撑结构优化[J]. 中国机械工程, 2020, 31(19): 2346-2354.
[8]	张静;马靓;赵登飞. 大方坯结晶器电磁搅拌器结构优化[J]. 中国机械工程, 2020, 31(10): 1148-1154.
[9]	初红艳1，2;许康健1，2;孙冬明1，2;蔡力钢1，2. 挤压旋转的橡胶辊滞后生热温度场分析[J]. 中国机械工程, 2019, 30(18): 2217-2223.
[10]	李拓1;白鸿柏1,2;薛新2;吴乙万2. 高温环境下编织-嵌槽型金属橡胶的疲劳特性分析[J]. 中国机械工程, 2019, 30(09): 1009-1017.
[11]	文均1，2;王东方1;雷基林1;李浙昆1;温志高2;代云辉3;辛千凡1. 活塞内冷油腔的振荡传热特性及位置的研究[J]. 中国机械工程, 2019, 30(06): 672-679.
[12]	周坤, 王文健, 刘启跃, 郭俊. [表面强化及损伤机理]钢轨打磨机理研究进展及展望[J]. 中国机械工程, 2019, 30(03): 284-294.
[13]	吕宁;郑健;赵欣;徐薇. 熔融沉积成形快速成形机加热构建平台的温度场分析及优化[J]. 中国机械工程, 2019, 30(01): 90-95.
[14]	牛小强1;雷基林1;邓晰文1;文均2;温志高2. 活塞顶面热障涂层对活塞热负荷的影响[J]. 中国机械工程, 2018, 29(12): 1499-1506.
[15]	潘勇1;王香耿1;程敏2,3;刘保国2. 考虑稳定性的非线性刚度转子系统振幅突变分叉集分析[J]. 中国机械工程, 2017, 28(20): 2441-2447.