Research on Polishing Process of Glass-ceramics by Ice Fixed Abrasive Polishing Pad with Grooves

China Mechanical Engineering ›› 2013, Vol. 24 ›› Issue (1): 20-24.

Previous Articles Next Articles

Research on Polishing Process of Glass-ceramics by Ice Fixed Abrasive Polishing Pad with Grooves

Yang Zhangyi;Zuo Dunwen;Sun Yuli;Tong Jute

Nanjing University of Aeronautics and Astronautics, Nanjing, 210016

Online:2013-01-10 Published:2013-01-23
Supported by:

National Natural Science Foundation of China（No. 51175260）;

Supported by China Postdoctoral Science Foundation（No. 201003583）;
Jiangsu Provincial Natural Science Foundation of China（No. BK2012796）

开槽冰冻固结磨料抛光微晶玻璃的工艺研究

杨张一;左敦稳;孙玉利;童巨特

南京航空航天大学,南京,210016

基金资助:
国家自然科学基金资助项目(51175260)；中国博士后科学基金特别资助金资助项目（201003583）；江苏省自然科学基金资助项目(BK2012796)；南京航空航天大学研究生创新基地(实验室)开放基金资助项目(kfjj20110228)
National Natural Science Foundation of China（No. 51175260）;

Supported by China Postdoctoral Science Foundation（No. 201003583）;
Jiangsu Provincial Natural Science Foundation of China（No. BK2012796）

Abstract

Abstract:

Mould pressing method was used to groove the micron-sized α-Al2O3 ice fixed abrasive polishing pad. The polishing process of glass-ceramics by ice-fixed-abrasive polishing pad with grooves was researched through orthogonal test of four factors and three levels, and the results were compared with the ice-fixed-abrasive polishing pad without grooves under the same experimental conditions. The results show that the material removal ratio increases about 40% in grooved condition, and the surface topography of glass-ceramics is improved slightly although with little scratches. Spindle speed influences the material removal ratio more greatly. 

Key words: groove, ice fixed abrasive polishing pad, glass-ceramics, removal ratio, orthogonal test

摘要：

采用成形模具热压法给微米级α-Al2O3冰冻固结磨料抛光垫开槽。设计四因素三水平正交试验,对开槽冰冻固结磨料抛光垫抛光微晶玻璃的工艺进行了研究,与同样试验条件下未开槽冰冻固结磨料抛光垫的抛光效果进行了对比分析。结果表明：开槽情况下的去除率比未开槽情况下的去除率提高40%左右,微晶玻璃表面形貌略有改善但出现划痕现象,主轴转速对材料去除率影响更为显著。



关键词: 开槽, 冰冻固结磨料抛光垫, 微晶玻璃, 去除率, 正交试验

CLC Number:

TG580

YANG Zhang-Yi, ZUO Dui-Wen, SUN Yu-Li, TONG Ju-Te. Research on Polishing Process of Glass-ceramics by Ice Fixed Abrasive Polishing Pad with Grooves[J]. China Mechanical Engineering, 2013, 24(1): 20-24.

杨张一, 左敦稳, 孙玉利, 童巨特. 开槽冰冻固结磨料抛光微晶玻璃的工艺研究[J]. 中国机械工程, 2013, 24(1): 20-24.

References

[1]苏建修，郭东明，康仁科，等.硅片化学机械抛光时运动形式对片内非均匀性的影响分析[J].中国机械工程，2005(9)：815-818.
Su Jianxiu, Guo Dongming, Kang Renke, et al. Analysis of Influences on Within-wafer-nouniformity Motion form in Wafer Chemical Mechanical[J]. China Mechanical Engineering, 2005(9):815-818.
[2]魏昕，熊伟，黄蕊慰，等.化学机械抛光中抛光垫的研究[J].金刚石与磨料模具工程，2004(5)：40-43.
Wei Xin, Xiong Wei, Huang Ruiwei, et al. Study on the Performances of Polishing Pad in Chemical Mechanical Polishing[J]. Diamond Abrasives Engineering, 2004(5):40-43.
[3]郭东明，康仁科，苏建修，等.超大规模集成电路制造中硅片平坦化技术的未来发展[J].机械工程学报，2003，39(10)：100-105.
Guo Dongming, Kang Renke, Su Jianxiu, et al. Future Development on Wafer Planarization Technology in ULSI Fabrication[J]. Chinese Journal of Mechanical Engineering, 2003, 39(10):100-105.
[4]Zuo D W, Sun Y L, Zhao Y F. Basic Research on Polishing with Ice Bonded Nanoabrasive Pad[J]. Journal of Vacuum Science & Technology, 2009, B(27):1514-1519.
[5]韩荣久，斐舒，王淑荣，等.微晶玻璃及其抛光[J].航空精密制造技术，2000，36(1)：7-12.
Han Rongjiu, Fei Shu, Wang Shurong, et al. Crystalline Glass and Its Polishing[J]. Aviation Precision Manufacturing Technology, 2000, 36(1):7-12.
[6]孙玉利.冰冻固结磨料化学机械抛光单晶硅片的基础研究[D].南京：南京航空航天大学，2008.
[7]Paul S, Bandyopadhyay P P, Chattopadhyay A B. Effect of Cryo-cooling in Grinding Steels[J]. Journal of Materials Processing Technology, 1993, 37(1/4):791-800.
[8]Cook L M. Chemical Processes in Glass Polishing[J]. Journal of Non-crystalline Solids, 1990, 120(1/3):152-171.
[9]Rosales-Yeomans D, Doi T, Kinoshita M, et al. Effect of Pad Groove Designs on the Frictional and Removal Rate Characteristics of ILD CMP[J]. Journal of the Electrochemical Society, 2005, 152(1):G62-G67.
[10]Gregory P M. Modeling CMP Transport and Kinetics at the Pad Groove Scale[J]. Materials Research Society, 2004, 816:159-164.
[11]李茂，朱永伟，左敦稳，等.偏心距在偏心抛光中对去除速率均匀性的影响[J].机械制造与自动化，2009，38(1)：29-33.
Li Mao, Zhu Yongwei, Zuo Dunwen, et al. Effect of Eccentricity on Material Removal Rate in Certain Eccentricity Polishing[J]. Machine Building & Automation, 2009, 38(1):29-33.

[1]	YU Changrui, LIU Liangbao, ZHOU Jinggang, ZHANG Han, HUANG Dong, ZHANG Ning, LI Xun. Optimization of Roller Burnishing Parameters for Concave Circular-arc Surfaces of Turbine Disk Mortise Grooves [J]. China Mechanical Engineering, 2026, 37(1): 60-65.
[2]	DANG Xu, LIU Tao, YAN Min, XU Zhiwei. Multi-objective Optimization of Precision Milling Parameters for Variable Cross-section Scrolls [J]. China Mechanical Engineering, 2025, 36(12): 2854-2861.
[3]	Liyun HAN, Xueping LI, Xiangkai MENG, Yangyang LIANG, Lihao ZHANG, Xudong PENG. Study on Dynamics Characteristics of Porous Matrix Hydrodynamic and Hydrostatic Mechanical Seals [J]. China Mechanical Engineering, 2025, 36(11): 2544-2553.
[4]	Wenqian LI, Zhanqiang LIU, Jinfu ZHAO, Bing WANG, Yukui CAI. Nanosecond Laser Machining of Spiral Grooves of Dry Gas Seal Rotational Ring Surfaces [J]. China Mechanical Engineering, 2025, 36(10): 2207-2214.
[5]	NIU Yanzhao1, LIU Hongwei1, SONG Yali2, ZHU Xianglong1, HUANG Jiamei2, KANG Renke1. Optimization and Experimental Study of Bolt Retreat Groove Rolling Wheels Based on Finite Element Simulation [J]. China Mechanical Engineering, 2025, 36(06): 1214-1221.
[6]	ZHANG Zhenfeng2, 3, XU Xueshi1, LIN Zhongliang2, 3, TANG Wei2, 3, LI Haonan1, SHAN Longlong2, 3, BAI Qingshun1. Processing Experiments of Folding Defects and Fatigue Property in Short End Bolts [J]. China Mechanical Engineering, 2025, 36(01): 29-37.
[7]	DANG Xu, LIU Tao, YAN Min, AN Feng. Optimization of Precison Milling Combined Parameters and Precise Prediction of Milling Forces for Thin-wall Complex Variable Cross-section Scrolls [J]. China Mechanical Engineering, 2024, 35(11): 1963-1970.
[8]	QI Maofu, SUN Yuantao, TIAN Chunlei, FENG Jiaqi. Shear Failure Mechanism Analysis and Optimum Design of 850 Ton Cold Shear Based on Orthogonal Test [J]. China Mechanical Engineering, 2024, 35(04): 752-759.
[9]	YAN Dinghu, ZHAO Jianshe, ZHANG Changhao, GAO Weizheng, ZHU Yin, . Flow Field Design and Experimental Research of ECM of Array Spherical Groove Structures with Variable Cross-sections [J]. China Mechanical Engineering, 2023, 34(23): 2824-2831.
[10]	YANG Zhonghao, JIANG Bingyan, MA Zhigao, YANG Di, ZHANG Lu, . Adjustment of Thickness Uniformity for Precision Electroformed Mold Insert [J]. China Mechanical Engineering, 2023, 34(21): 2531-2539.
[11]	ZHAO Chuang, ZHAO Yugang, ZHAO Dandan, MENG Shuo, YU Hanlin, LI Zhihao, CAO Chen, ZHANG Haiyun, MENG Jianbing. Study on Groove Structures of Inconel 718 Alloy Fabricated by WJGL [J]. China Mechanical Engineering, 2023, 34(20): 2403-2410.
[12]	ZHAO Zemin, WANG Lihua, HUANG Hongyi, CHEN Taimao, JIANG Wei. Effects of Dynamic Stabilization Operation Parameters on Ballast Stability [J]. China Mechanical Engineering, 2023, 34(19): 2313-2319，2369.
[13]	XIANG Routong, WANG Shilong, ZHOU Jie, YI Lili. Study on Pressure Response Characteristics of New Pneumatic Position Sensor under Irradiation Environments [J]. China Mechanical Engineering, 2023, 34(11): 1364-1371.
[14]	DUAN Lingyun, HUANG Chuanzhen, LIU Dun, YAO Peng, LIU Hanlian. An Experimental Investigation of Laser Assisted Waterjet Microgrooving of GaAs Wafers [J]. China Mechanical Engineering, 2023, 34(10): 1172-1183.
[15]	CHEN Yupeng, WANG Haibo, XUE Chaojun, ZOU Huaijing, GAO Yimin, . Dynamics Simulation and Experimental Study of Industrial Assembly Anti-vibration Exoskeletons [J]. China Mechanical Engineering, 2023, 34(04): 404-413.

Research on Polishing Process of Glass-ceramics by Ice Fixed Abrasive Polishing Pad with Grooves

开槽冰冻固结磨料抛光微晶玻璃的工艺研究

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics