Influences of Coating Performance on Longitudinal Modal Propagation Characteristics of Gas Pipelines

Abstract

Abstract: The propagation characteristics of the longitudinal modes in the viscoelastic coatings were analyzed theoretically，and the dispersion and attenuation characteristics of the longitudinal mode，especially the L（0，2) mode，were studied.A three-dimensional finite element model of the asphalt coating pipes was established.The influences of the excitation frequency，the coating density and the attenuation coefficient of the coating wave on the guided wave propagation was studied，and the excitation and reception of the asphalt clad steel pipe toward L（0，2) modal experiments were carried out.The results show that in the low frequency ranges，as the excitation frequency and the coating density increase，the L（0，2) mode is also affected by the asphalt coatings，and the energy attenuation is gradually increased.The attenuation curves may be used as the theoretical guidance for the modal selection of the pipelines with asphalt coatings.The low frequency longitudinal mode ultrasonic guided waves are better for the detection of the pipelines with low density coatings.

Key words: coating, longitudinal mode, attenuation characteristic, density, longitudinal wave attenuation coefficient

摘要： 对带黏弹性包覆层管道中纵向模态的传播特性进行了理论分析，对纵向模态尤其是L（0，2)模态的频散和衰减特性进行了研究。建立了沥青包覆层管道的三维有限元模型，研究了激励频率、包覆层密度以及包覆层纵波衰减系数对导波传播的影响，并在带沥青包覆层钢管中进行激励和接收 L（0，2)模态的实验。结果表明，在低频范围下，随着激励频率和包覆层密度的增大，L（0，2)模态受沥青包覆层的影响也增加，其能量衰减也逐渐增大；对于带沥青包覆层的管道，其衰减频散曲线可用作模态选取的理论指导，采用低频纵向模态超声导波对带低密度包覆层管道检测时效果较好。

关键词: 包覆层, 纵向模态, 衰减特性, 密度, 纵波衰减系数

CLC Number:

TB599

CAI Haichao1,2;SHANG Zhendong1,2;CHAO Hongjun3. Influences of Coating Performance on Longitudinal Modal Propagation Characteristics of Gas Pipelines[J]. China Mechanical Engineering.

蔡海潮1,2;尚振东1,2;晁红军3. 包覆层性能对输气管道纵向模态导波传播特性的影响[J]. 中国机械工程.

References

[1]ROSE J L.GUIDED WAVES Successes and Challenges for Ultrasonic Testing in NDT and SHM[J].Materials Evaluation,2010，68（5）：495-500.
[2]何存富,刘增华,孙雅欣,等.基于超声导波技术对弯管中缺陷检测的实验研究[J].中国机械工程,2005,16（18）：1662-1665.
HE Cunfu，LIU Zenghua，SUN Yaxin，et al.Experimental Study on Defect Detection in Curved Pipes Using Ultrasonic Guided Waves Technique[J].China Mechanical Engineering，2005,16（18）：1662-1665.
[3]CARANDENTE R，CAWLEY P. A Method to Estimate the Size of Corrosion Patches with Guided Waves in Pipes[J].Review of Progress in Quantitative Nondestructive Evaluation,2012，1430（1）：1929-1936.
[4]KWUN H，KIM S Y，CHOI M S，et al.Torsional Guided-wave Attenuation in Coal-tar-enamel-coated，Buried Piping[J].Ndt & E International,2004，37（8）：663-665.
[5]ALLEYNE D N，PAVLAKOVIC B，LOWE M J S，et al.Rapid Long-range Inspection of Chemical Plant Pipework Using Guided Waves[J].Key Engineering Materials,2001,270/273-（1）：434-441.
[6]SHIN H J，SONG S J，PARK J S.Long Range Inspection of Polyethylene Coated Steel Pipes by Using Guided Waves[C]//Review of Progress in Quantitative Nondestructive Evaluation.Brunswick，2001:1194-1201.
[7]BARSHINGER J，ROSE J L，AVIOLI M J.Guided Wave Resonance Tuning for Pipe Inspection[J].Journal of Pressure Vessel Technology-Transactions of the ASME,2002，124（3）：303-310.
[8]BARSHINGER J N，ROSE J L.Ultrasonic Guided Wave Propagation in Pipes with Viscoelastic Coatings[M].Review of Progress in Quantitative Nondestructive Evaluation,2002,615:239-246.
[9]BARSHINGER J N，ROSE J L.Guided Wave Propagation in an Elastic Hollow Cylinder Coated with a Viscoelastic Material[J].IEEE Transactions on Ultrasonics Ferroelectrics and Frequency Control,2004，51（11）：1547-1556.
[10]HUA J，ROSE J L.Guided Wave Inspection Penetration Power in Viscoelastic Coated Pipes[J].Or Insight,2010，52（4）：195-205.
[11]KIRBY R，ZLATEV Z，MUDGE P.On the Scattering of Longitudinal Elastic Waves from Axisymmetric Defects in Coated Pipes[J].Journal of Sound and Vibration,2013，332（20）：5040-5058.
[12]沈立华，王悦民，郑明雪，等.基于磁致伸缩效应导波的数值模拟和实验研究[J].中国机械工程，2007,18（5）：532-535.
SHEN Lihua，WANG Yuemin，ZHENG Mingxue，et al.Numerical Simulation and Experimental Research on Guided Waves Based on Mangentostrictive Effect[J].China Mechanical Engineering，2007,18（5）：532-535.
[13]何存富，李伟，吴斌.扭转模态导波检测管道纵向缺陷的数值模拟[J].北京工业大学学报，2007,33（10）:1009-1013.
HE Cunfu，LI Wei，WU Bin.Numerical Simulation of Longitudinal Crack Detection in Pipes Using Ultrasonic Guided wave T（0,1） Mode[J].Journal of Beijing University of Technology，2007，33（10）:1009-1013.

[1]	WANG Guangyang, JI Xiaogang, NIU Guofa, MEI Jianchi. Density Gradient IWP Lattice Structural Force-energy Synergistic Response [J]. China Mechanical Engineering, 2026, 37(1): 192-200.
[2]	WU Jianpeng, DING Ao, MA Biao, LI Heyan, WANG Liyong, YANG Chengbing. Failure Probability Analysis of Temperature Field in Wet Friction Components Based on Macro-Micro Frictional Contact Model [J]. China Mechanical Engineering, 2026, 37(1): 40-50.
[3]	Zengwei LI, Zewei HOU, Jiawang HONG, Junyi QI. Failure Analysis of a Certain Type of Hook Suspension Based on Cohesive Zone Model [J]. China Mechanical Engineering, 2025, 36(09): 1934-1941.
[4]	WANG Weiping, ZHOU Xinyi, LU Shun. High Energy Density Hydraulic Energy Storage Method Based on Composite Principle of Gas Liquid Dissolution and Gas Compression [J]. China Mechanical Engineering, 2025, 36(03): 426-434，443.
[5]	LIN Jiahui, LI Zhuangzhuang, LI Xuelin, LI Jun. A New Method for Path-engulfment Topology Optimization [J]. China Mechanical Engineering, 2025, 36(03): 504-514.
[6]	LI Xinyu1, 2, 3, ZHOU Yonghua1, 2, 3. Mesoscale Numerical Simulation of SLM Processes for Al-Mn-Sc-Zr [J]. China Mechanical Engineering, 2025, 36(03): 584-592，603.
[7]	WANG Jing1, 2, AI Chao1, YUAN Xiao2, ZHU Xun2, GUO Fei2. Performance Comparison of High-speed Laser Cladding Martensitic Stainless-steel Coatings and Electroplating Coatings [J]. China Mechanical Engineering, 2024, 35(08): 1480-1488.
[8]	MA Chao1, 2, ZHANG Jianjian2, 3, WANG Ningning2, 3, GUO Shanshan1, 2. Flow Channel Wall Erosion Characteristics and Impacts on Performance in Radial Turbines [J]. China Mechanical Engineering, 2024, 35(07): 1232-1240.
[9]	HAN Xiaohui, LIN Sen, FANG Xifeng, WANG Zhenzhong, SUN Zhaogang, YU Feilong, LI Lei, MA Yunwu, LI Yongbing, . Influence of Rivet Coating on Formation and Mechanics Performances of SSFR Joints [J]. China Mechanical Engineering, 2024, 35(04): 721-730.
[10]	LI Rongqi, YAN Tao, HE Zhicheng, MI Dong, JIANG Chao, ZHENG Jing. A Topology Optimized Design Method for High-performance Structures with Fluid-thermal-mechanics Coupling [J]. China Mechanical Engineering, 2024, 35(03): 487-497.
[11]	ZHAO Chuang, ZHAO Yugang, ZHAO Dandan, MENG Shuo, YU Hanlin, LI Zhihao, CAO Chen, ZHANG Haiyun, MENG Jianbing. Study on Groove Structures of Inconel 718 Alloy Fabricated by WJGL [J]. China Mechanical Engineering, 2023, 34(20): 2403-2410.
[12]	KE Qingdi, LUO Junyou, JIANG Shouzhi, HUANG Haihong, . Construction of Ultrasonic-Stress Inversion Model Based on Distribution States of Coating Materials [J]. China Mechanical Engineering, 2023, 34(18): 2230-2237.
[13]	YU Zhihao, ZHANG Guangming, LI Hongke, DUAN Peikai, YU Zun, TAI Yuping, LI Wenhai, XU Quan, ZHAO Jiawei, LAN Hongbo. Electric-field-driven Jet Deposition Micro 3D Printing of High Resolution Aluminum Nitride Ceramic-based Circuits [J]. China Mechanical Engineering, 2023, 34(11): 1353-1363.
[14]	GUO Wenguang, WANG Fei. Braking Torque Model in Liquid-cooled Permanent-magnet Retarders Accounting for Temperature Effects [J]. China Mechanical Engineering, 2023, 34(06): 685-693.
[15]	MENG Liang, ZHONG Mingzhe, LI Wenbiao, XIA Liang, GAO Tong, ZHU Jihong, ZHANG Weihong, . Topology Optimization Design of Aero-engine External System Brackets for Additive Manufacturing [J]. China Mechanical Engineering, 2022, 33(23): 2822-2832.