Chip Formation in High Speed Milling of Hardened Mold Steel

China Mechanical Engineering ›› 2013, Vol. 24 ›› Issue (14): 1939-1942,1950.

Previous Articles Next Articles

Chip Formation in High Speed Milling of Hardened Mold Steel

Pang Junzhong1,2;Xin Zhijie1;Shen Xingquan1;Miao Hongbin1

1.North University of China，Taiyuan,030051
2.Key Laboratory for Precision and Non-traditional Machining Technology of Ministry of Education,Dalian University of Technology,Dalian,Liaoning,116024

Online:2013-07-25 Published:2013-07-29
Supported by:

National Natural Science Foundation of China（No. 51175482）;
Shanxi Provincial Natural Science Foundation of China（No. 2013011024-4）

高速铣削淬硬模具钢的切屑变形

庞俊忠1，2;辛志杰1;沈兴全1;苗鸿宾1

1.中北大学，太原，030051
2.大连理工大学精密和特种加工教育部重点实验室，大连，116024

基金资助:
国家自然科学基金资助项目（51175482）；山西省自然科学基金资助项目(2013011024-4)
National Natural Science Foundation of China（No. 51175482）;
Shanxi Provincial Natural Science Foundation of China（No. 2013011024-4）

Abstract

Abstract:

Using solid carbide straight end mills with TiAlN coating, P20 steel was machined in the cutting speed range of 200 to 942m/min. The chip formations at various speeds were investigated. The saw-tooth chips with adiabatic shear bands are observed at 754 to 942m/min with P20 steel of 41HRC, but for P20 steel of 32HRC, they are formed at 848 to 942m/min. Cutting speed and workpiece hardness are found to have significant influences on chip formation. Based on micro-measurement of the chips, a calculation model for saw-tooth chip formation during high speed end milling of hardened steel was proposed. The results show that the average shear strain and shear strain rate are within the shear bands, and the saw-tooth frequency increases rapidly by increasing cutting speed, and their maximums at 942m/min exceed 23, 107s－1 and 244kHz respectively.

Key words: chip formation, calculation model, hardened mold steel, high speed milling

摘要：

使用TiAlN涂层整体圆柱立铣刀，以200～942m/min的铣削速度，对淬硬P20钢进行了高速铣削试验，研究了各种切削速度下的切屑变形。对于淬火硬度为41HRC的P20钢，切削速度为754～942m/min时，形成了带有绝热剪切带的锯齿形切屑;对于淬火硬度为32HRC的P20钢，锯齿形切屑形成的切削速度是848～942m/min;切削速度和工件硬度对切屑变形有着重要的影响。基于切屑纵截面尺寸的微观测量，建立了高速铣削淬硬钢时锯齿形切屑变形的计算模型。结果显示：应变、应变率和锯齿频率随切削速度增大而快速增大，在切削速度为942m/min时，它们分别高达23、107s－1和244kHz。

关键词: 切屑变形, 计算模型, 淬硬模具钢, 高速铣削

CLC Number:

TG506.1

LONG Dun-Zhong-1, 2, XIN Zhi-Jie-1, CHEN Xin-Quan-1, MIAO Hong-Bin-1. Chip Formation in High Speed Milling of Hardened Mold Steel[J]. China Mechanical Engineering, 2013, 24(14): 1939-1942,1950.

庞俊忠1, 2, 辛志杰1, 沈兴全1, 苗鸿宾1. 高速铣削淬硬模具钢的切屑变形[J]. 中国机械工程, 2013, 24(14): 1939-1942,1950.

[1]	NIU Wenchao, SUN Zhaoyang, SHENG Zhongqi, YU Jiancheng, ZHAO Baode, ZHAO Wentao, . Study on Influencing Factors of Stress at Roots of Autonomous Sailboat Wing Sail Mast and Its Influencing Laws [J]. China Mechanical Engineering, 2023, 34(22): 2647-2658.
[2]	ZHANG Lifeng, ZHANG Xiaoguang. Machining Performance and Material Removal Mechanism of High-speed Milling of CFRP with Variable Angle under Minimal Quantity Lubrication [J]. China Mechanical Engineering, 2023, 34(21): 2622-2628.
[3]	NI Jing, SUN Jingbo, HE Lihua, CUI Zhi, XUE Fei. Study on Chip Forming Characteristics of Orthogonal Cutting of PTFE Materials [J]. China Mechanical Engineering, 2022, 33(22): 2733-2740.
[4]	LI Yousheng. Influences of TaC(NbC) on Cemented Carbide Tool Wear Resistance in High Speed Milling [J]. China Mechanical Engineering, 2020, 31(13): 1601-1605.
[5]	Qi Xiangdong, Lian Jiachuang, Dong Zhikui. Calculation and Experimental Analysis of Stretch-bend Straightening Elongation [J]. China Mechanical Engineering, 2016, 27(08): 1113-1116.
[6]	Liu Bo, Zhou Houming, Zhou Youhang, Zhang Gaofeng, Peng Ruitao. Analysis of Influence of Cutter Diameter on Mechanics Propertiesof Shrink-fit Holder and Cutting Tool [J]. China Mechanical Engineering, 2016, 27(04): 513-517,525.
[7]	Jing Lulu, Chen Ming, An Qinglong. Experimental Study of Saw-tooth Chip Formation in Hard Cutting of SKD11 [J]. China Mechanical Engineering, 2014, 25(23): 3151-3154,3159.
[8]	LI Fei-Long, GUO Kong-Hui, YANG Yan-Beng, CHEN Die-Song. Research on Assessment of Energy Saving in Light-weight of Automotive Material Based on GREET Model [J]. China Mechanical Engineering, 2013, 24(5): 681-685.
[9]	XIN Shua-Rong-1, 2, CHAN Long-Long-1, 3. An Experiential Calculation Method to Radial Extrusion Pressure by Floating-die [J]. China Mechanical Engineering, 2013, 24(4): 547-551.
[10]	HE Kong-De-1, 2, LI You-Rong-1, FANG Zi-Fan-2, YANG Wei-Hua-1, 2. Calculation Model and Numerical Simulation for Underwater Mooring Monitoring Platform Dynamic Response [J]. China Mechanical Engineering, 2013, 24(4): 432-436,451.
[11]	Yao Qishui;Zhang Ran;Ming Xingzu;Yang Wen. Static Radial Stiffness Analysis of Elastic Composite Cylindrical Roller Bearings [J]. China Mechanical Engineering, 2013, 24(22): 3085-3089.
[12]	LIU Wei-Wei, LI Feng, LIN Jun-Hua, WEI Yuan. Research on Surface Roughness Based on SPSO in High Speed Milling of GH4169 [J]. China Mechanical Engineering, 2011, 22(22): 2654-2657,2771.
[13]	ZHANG Wei-Wen, GUO Gang, HUANG Yun, HUANG Zhi. A Molecular Dynamics Study of Chip Formation on Nano-grinding Processes [J]. China Mechanical Engineering, 2011, 22(2): 127-132.
[14]	SU Yu, HE Ning, LI Liang. Experimental Study on High Speed Milling Titanium Alloys Using Cryogenic Minimum Quantity Lubrication [J]. China Mechanical Engineering, 2010, 21(22): 2665-2670.
[15]	XU Xiao-Lin, HUANG Shu-Chao, DIAO Wen-Zhen, ZHOU Li, ZHOU Jia-Lin. Study on Surface Morphology and Chip Formation by High-speed Milling of High Volume Fraction SiCp/Al Composites [J]. China Mechanical Engineering, 2010, 21(05): 519-524.

Chip Formation in High Speed Milling of Hardened Mold Steel

高速铣削淬硬模具钢的切屑变形

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics